Toro Workman - Controls; Control Panel Layout; Pedal Operation (Accelerator and Brake)

To Next Page

To Previous Page

Controls

Becomefamiliarwithallthecontrolsbeforeyoustarttheengineandoperatethemachine.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

ControlPanel

g033921

Figure6

1.Steeringwheel6.USBpowerpoint

2.Gear-shiftindicator

7.Parking-brakelever

3.Gear-shiftlever8.Chokecontrol

4.Hornbutton(Internationalmodelsonly)

9.Brakepedal

5.Keyswitch10.Acceleratorpedal

AcceleratorPedal

Usetheacceleratorpedal(Figure6)tovarythe

groundspeedofthemachine.Pressingdownthe

acceleratorpedalstartstheengine.Pressingthe

pedalfartherincreasesthegroundspeed.Releasing

thepedalslowsthemachine,andtheengineshutsoff.

Note:Themaximumforwardspeedis26km/h

(16mph).

BrakePedal

Usethebrakepedaltostoporslowthemachine

(Figure6).

CAUTION

Operatingamachinewithwornorincorrectly

adjustedbrakescanmayresultinpersonal

injury.

Ifthebrakepedaltravelstowithin25mm(1

inch)ofthemachineoorboard,adjustor

repairthebrakes.

Main Page

Table of Contents3
Safety4
General Safety4
Safety and Instructional Decals5
Setup8
Installing the Steering Wheel (International Models Only)8
Checking the Fluid Levels and Tire Pressure8
Burnishing the Brakes9
Reading the Manual and Viewing the Setup Material9
Product Overview10
Controls11
Specifications14
Attachments/Accessories14
Before Operation15
Before Operation Safety15
Performing Daily Maintenance15
Checking the Tire Pressure15
Adding Fuel16
Breaking in a New Machine16
During Operation17
During Operation Safety17
Operating the Cargo Bed19
Using the Rear Cargo Bed Accessory Mount21
Loading the Cargo Bed22
Starting the Engine22
Stopping the Machine23
Parking the Machine23
After Operation23
After Operation Safety23
Hauling the Machine23
Towing the Machine24
Towing a Trailer24
Maintenance25
Maintenance Safety25
Recommended Maintenance Schedule(S)26
Daily Maintenance Checklist28
Maintaining the Machine under Special Operating Conditions28
Pre-Maintenance Procedures29
Preparing the Machine for Maintenance29
Lifting the Machine29
Accessing the Hood30
Raising and Lowering the Seat Assembly30
Removing a Bucket Seat30
Installing a Bucket Seat31
Removing a Bench Cushion31
Installing a Bench Cushion31
Lubrication32
Greasing the Machine32
Greasing the Front Wheel Bearings32
Engine Maintenance36
Engine Safety36
Servicing the Air Cleaner36
Servicing the Engine Oil38
Servicing the Spark Plug39
Adjusting the High/Low Idle40
Fuel System Maintenance40
Inspecting Fuel Lines and Connections40
Replacing the Fuel Filter40
Servicing the Carbon Canister41
Electrical System Maintenance42
Electrical System Safety42
Servicing the Battery42
Replacing the Fuses44
Maintaining the Headlights45
Drive System Maintenance46
Maintaining the Tires46
Inspecting the Steering and Suspension Components46
Adjusting the Front Wheel Alignment47
Checking the Transaxle-Fluid Level48
Changing the Transaxle Fluid48
Checking the Neutral Gear-Shift Position48
Adjusting the Neutral Gear-Shift Position49
Maintaining the Primary Drive Clutch49
Reducing the Top Speed49
Cooling System Maintenance50
Cooling System Safety50
Cleaning the Engine-Cooling Areas50
Brake Maintenance51
Checking the Parking Brake51
Adjusting the Parking Brake51
Checking the Brake-Fluid Level51
Inspecting the Brakes52
Replacing the Service and Parking-Brake Pads52
Changing the Brake Fluid52
Belt Maintenance53
Servicing the Drive Belt53
Adjusting the Starter-Generator Belt53
Chassis Maintenance54
Adjusting the Cargo-Bed Latches54
Cleaning54
Washing the Machine54
Storage55
Storage Safety55
Storing the Machine55

Toro Workman - Controls; Control Panel Layout; Pedal Operation (Accelerator and Brake)

Table of Contents

Related product manuals