To
tune to a channel
or
input
in Select mode:
Setting
the
Channel
Tuning
Mode
This
feature allows you to
choose
how tuning will be
handled
for
analog
and
digital
channels
when the
TV
is in
Antenna
mode.
Note:
To
use
this
feature,
the
Input Configuration
must be set
to
Antenna
(1&
page
30).
The
channel
tuning
mode
has three options.
Both
analog
and digital
channels
can
be tuned normally
1
BACK
NEXT
While watching
TV,
press I§)
~
or
Q!jJ
~
to open the
Channel
Browser™
and surf back to a previous item
or forward
to
the next item in the list.
In
Select
mode,
when you
stop
on
an item in the
Channel
Browser™,
it will
be
highlighted but you
must press
@ to tune the
TV
to the highlighted
item.
2 Press @ to tune the
TV
to the highlighted item.
3
EXIT
Press 0 to close the
Channel
Browser
nl
.
.
Mode'
Standard
.'.
~
- .
j.;
Des:crJpJion
~--
-
-.,.'
To
set
the
Channel
Tuning Mode:
Note:
Digital mode will
be
most useful after
analog channels are shut down
by
the
government
in
2009.
1
From
the
Setup
menu, highlight Installation
and
press @. A new set
of
Installation
menu
icons
will appear.
2
Open
the
Terrestrial
menu, highlight
Channel
Tuning
Mode,
and then press
~
to select
your
desired mode.
Note:
•
The
Channel Options windows as well as
the Channel Browser ANT/CABLE list will
be
updated automatically when you change the
mode. Also, the History List will be cleared, but
the Favorites List will
be
saved.
• Even
if
the Channel Tuning Mode
is
set to
Digital, analog channel 3 will still
be
the
default channel to prevent the initial case
where no digital channels have been found
in
prior channel scans. (Channel Options will not
have anything listed until a scan
is
done.)
Only
digital channels
can
be
tuned
Digital channels will have priority when
manually entering a channel
number
using the Channel
Number
(0-9) on the
remote control, analoG channels can
still be tuned by
~
/~,
if
available
Digital
Auto
(default)
Note: Whenever an item
is
selected that cannot
be tuned (for various reasons), the
TV
will
automatically tune to the previously viewed
channel or input.
Clearing channels from the History List:
•
Recontiguring
the
ANT/CABLE
input will
clear
the
History List.
Note: See
page
30
for details on configuring
the antenna input.
• Once 32 channels
or
inputs are stored
in
the History
List, the oldest item will be removed from the list
when a new channel
or
input
is
tuned.
• Turning
off
the
TV
will
clear
the History List.
Adding channels
and
inputs to the History
List:
As a channel or input
is
tuned, the Channel
Browser™
adds it to the History List and displays
it
on the "right
side"
of
the Channel Browser™. Previously tuned
channels/inputs are "shifted" to the left, eventually
BACK
moving
off
the left side. Press I§)
~
to
surf
backward
through the previously tuned channels/inputs. Any
channel or input that
is
tuned repeatedly will not be
repeated in the History List, but instead is moved to
the end
of
the list on the right side
of
the Channel
Browser™.
The
Channel Browser™ will store
the
following
channels:
• All channels that are tuned using the numeric buttons
on the remote control.
• All channels that are
tuned
using
~
or
~
on the
remote control.
Adding
and
clearing
channels
and
inputs
in
the
History
List
I
38
To Next Page
Loading...
