Tuning
to
the
next
programmed
channel
To
tune
to
the
next
programmed
channel:
Press
(ts)
or
~
on the remote control
or
TV
control
panel.
Note:
This
feature will not work unless you
program channels into the
TV's
channel memory
(1&
page
31).
Tuning
to
a
specific
channel
(programmed
or
unprogrammed)
Tuning
analog
channels:
Press the Channel
Number
(0-9)
on the remote
control. For example, to select channel 125, press
I,
2,
5,
then@.
TIming digital channels:
Press the Channel
Number
(0-9)
on the remote
control, followed by the dash
("1QQ)
button and then
the sub-channel number. For example, to select digital
channel 125-1, press l, 2, 5,
-,
I,
then
@.
Note:
If
a digital channel is
not
programmed-
either through the automatic channel scan
(1&
page
31)
or
the Channel
add
function
(1&
page
32)-you
will have
to
tune the RF channel using
the Channel
Number
and
dash
«1QQ))
on the
remote control.
Switching
between
two
channels
using
Channel
Return
The
Channel Return feature allows you
to
switch
between two channels without entering an actual
channel number each time.
1 Select the first channel you want to view.
2 Select a second channel using the Channel
Number
buttons (and the dash
("1QQ)
button
if
selecting a digital channel).
3
CH
RTN .
Press 0 on the remote control. The prevIous
.
CH
RTN
channel will dIsplay. Each time you press 0 , the
TV
wi
II
switch back and forth between the last two
channels that were tuned.
CH
RTN
Note:
If
you press 0 from a non-antenna
input, the
TV
will return to the last-viewed
input.
Switching
between
two
channels
using
SurfLock™
The
SurtLock™ feature temporarily
"memorizes"
one
CHRTN
channel to the 0 button, so you can return to that
channel quickly from any other channel by pressing
CH
RTN.
CH Rrt.I
o .To
memonze
a channel to the 0 button:
1 Tune the
TV
to the channel you want to program
· CH RTN
IOtO
the 0 button.
2
CH
RTN
.
Press
and
hold 0 for about 2
seconds
until
the message
"Memorized"
appears on-screen.
CHRTN
The
channel has been
programmed
to the 0
button.
3
You
can then
change
channels
repeatedly, and
CH
RTN .
when you press 0
,the
memonzed
channel
will be tuned.
The
TV
will return to the memorized channel
one
.
CH
RTN
time only.
Once
you press 0 and then
change
channels again, the
CH
RTN
memory
will be cleared
and the button will function as Channel Return,
by switching back and forth between the last
two
channels that are tuned.
This
feature also works for
external inputs.
Selecting
the
picture
size
You
can view many program formats
in
a variety
of
picture
sizes-Natural,
TheaterWide
1,
TheaterWide
2, TheaterWide
3,
Full,
4:3
HD,
Native, and
Dot
by
Dot
(available in PC Mode Only).
Note:
The
"picture size" illustrations are
examples only
The
format
of
the image (in any
of
the picture sizes) will vary depending on the
format
of
the signal you are currently watching.
Select the picture size that displays the current
program the way that looks
best
to
you.
You can save separate picture size preferences for
each input on
your
TV.
To select
the
picture
size using
the
remote
control:
1
PIC SIZE
Press 0 on the remote control.
2
While
the Picture Size screen
is
open,
you can
do
one
of
the following to select the desired picture
size:
PIC SIZE
• Repeatedly press 0 .
• Press the corresponding
Number
button
(0-6)
while the Picture Size screen
is
open.
•
Press'"
or
...
while the Picture Size screen is
open.
(continued)
39
I
To Next Page
Loading...
