Note:
When
you turn on the Audio Receiver,
change its input source,
or
adjust the sound
volume, the sound will be output from the audio
receiver's speakers even
if TV Speakers has
been selected.
Turn
the
TV
off
and
on again to
output the sound from the
TV
speakers.
Speaker
Preference
From this item, you can set your audio
output preference
to
the TV speakers
or the audio receiver speakers. When
this item
is
set
to
Audio Receiver,
the TV remote can be used
to
adjust
or mute the volume
of
the audio.
This item will be grayed out unless
a REGZA-LlNK compatible audio
receiver
is
connected.
• Stereo, Mono or
SAP
audio status (when HDMI input
mode, Dolby Digital or PCM)
• Video resolution
• Aspect ratio
of
incoming video signal (4:3 or 16:9)
• V-Chip rating status
•
Game
Timer (if set)
1_.
C··t1iMi'Mnauiim
M
d4d1*
• : J '
To
close the
RECALL
screen:
RECALL
.
Press 0 agaill.
To
display
TV
status information using INFO:
To
set the REGZA-LINK® Setup:
1 From the
Setup
menu,
highlight
REGZA-L1NK
Setup
and press
@.
2
Press.
or
T to highlight
Enable
REGZA-L1NK.
3 Press
....
or
~
to select
On.
Note:
If
you select
Enable
REGZA-LINK
Off,
the
other items will be
grayed
out.
4
Press.
or
T to highlight the
REGZA-L1NK
Setup
item you want to use, and press
....
or
~
to
select
On
or
desired mode.
•
TV
Auto
Input Switch:
On/Off
•
TV
Auto
Power:
On/Off
• Device
Auto
Standby:
On/Off
• Speaker Preference:
TV
Speakers/Audio Receiver
5 To save the new settings, highlight
Done
and
press
@. To revert to the factory defaults,
highlight
Reset
and press @.
Displaying
TV
status
information
To
display TV status information using
RECALL:
RECALL
Press 0
on
the
remote
control.
The following information will display (if applicable):
•
Current
input
(ANT/CABLE,
VIDEO
1,
etc.)
• IfANT/CABLE
is
the current input, either "CABLE"
(for cable TV) or "ANT" (for over-the-air broadcasts).
• Channel number (if in
ANT/CABLE
mode)
• Channel label (if set)
• Digital signal strength indicator (bar graph in lower
right corner
of
box; for ATSC signal only)
58
INFO
Press
0 on the
remote
control.
The
following additional information will
display
for
off
air digital
channels
(if
applicable):
• Title
• Duration
•
Detailed
description
MLB
Young'5
XXX..
9:00pm'
11.00pm
EST
Today
:$
Malor
Leagua 8or.ebol1
Note:
The
location
of
the banner can
be
moved
to
the top or bottom
of
the screen
by
pressing.
or T while the RECALL or INFO display
is
on-
screen.
Understanding
the
auto
power
off
feature
The TV will automatically tum itself off after
approximately
15
minutes if it
is
tuned
to
a vacant
channel or a station that completes its broadcast for the
day. This feature functions
in
ANT/CABLE
mode only.
Understanding
the
last
mode
memory
feature
If
the
power
is
cut
off while you
are
viewing
the
TV, the
Last
Mode
Memory
feature
automatically
turns
on
the
TV
when
the
power is resupplied.
Note:
If
it's possible,
and
you will
be
away
from the
TV
for an extended
period
of
time you
should unplug the
power
cord.
To Next Page
Loading...
