Why won't the media feed in my Toshiba Barcode Reader?
If the media won't feed in your Toshiba Barcode Reader, it might not be loaded properly, or the printer is in an error condition. Load the media properly. Solve the error indicated in the message display.
What does MEMORY WRITE ERR mean on Toshiba B-EP2?
A 'MEMORY WRITE ERR.' on your Toshiba Barcode Reader indicates an error occurred while writing to the flash ROM/USB memory. Turn the printer off, and then on again.
What to do if my Toshiba B-EP2 says PAPER JAM?
If your Toshiba Barcode Reader displays a 'PAPER JAM' error, it could be due to several reasons. The media might be jammed, not loaded properly, the wrong media sensor might be selected, the black mark sensor might be misaligned, or the media size might not match the programmed size. First, remove any jammed media and clean the platen. Then, reload the media correctly and press the [RESTART] key. If the issue persists, ensure the correct media sensor is selected and realign the black mark sensor if necessary. Check if the loaded media size matches the programmed size. As a last resort, turn the printer off and then on.
What to do if my Toshiba B-EP2 shows CUTTER ERROR?
A 'CUTTER ERROR' on your Toshiba Barcode Reader (if a cutter module is installed) indicates that the media is jammed in the cutter or the cutter cover is not attached properly. Remove any jammed media. Press the [RESTART] key. Ensure the Cutter Cover is properly attached.
Why is the printed image blurred on my Toshiba B-EP2?
If the printed image from your Toshiba Barcode Reader is blurred, the combination of the ribbon and media might not be correct, or the print head might be dirty. Select an appropriate ribbon for the media type being used. Clean the print head using the Print Head Cleaner or a cotton swab slightly moistened with ethyl alcohol.
What to do if Toshiba Barcode Reader shows HEAD OPEN error?
The 'HEAD OPEN' error on your Toshiba Barcode Reader means the Print Head Block is open. If the Print Head Block is opened in Online mode, or if feeding or printing has been attempted with the Print Head Block open, close the Print Head Block. If feeding or printing was attempted, press the [RESTART] key after closing it.
What does SYSTEM ERROR mean on my Toshiba Barcode Reader?
A 'SYSTEM ERROR' on your Toshiba Barcode Reader can be caused by several factors. The printer might be in a noisy location, the power cord may not be grounded, it could be sharing a power source, or there might be an issue with the application software on your host computer. Keep the printer and interface cables away from noise sources. Ensure the power cord is grounded and provide an exclusive power source for the printer. Confirm that the host computer operates properly.
Why is my Toshiba B-EP2 printing nothing on the media?
If your Toshiba Barcode Reader is printing nothing on the media, it could be due to several reasons. The media or ribbon may not be loaded properly, the print head might not be installed correctly, or the combination of ribbon and media may be incorrect. Load the media and ribbon properly. Ensure the print head is correctly installed and the Print Head Block is closed. Select an appropriate ribbon for the media type being used.
How to troubleshoot a Toshiba B-EP2 that will not turn on?
If your Toshiba Barcode Reader won't turn on, the power cord may be disconnected, the AC outlet might not be working, or the fuse could be blown. First, plug in the power cord. If that doesn't work, test the AC outlet with another electrical appliance. Finally, check the fuse or circuit breaker.
Why does my Toshiba B-EP2 Barcode Reader show a COMMS ERROR?
A 'COMMS ERROR' on your Toshiba Barcode Reader indicates a communication issue. Ensure the interface cable is correctly connected to both the printer and the host, and verify that the host is turned on.
General| Brand | Toshiba |
|---|---|
| Model | B-EP2 |
| Category | Barcode Reader |
| Language | English |
To Next Page