EasyManua.ls Logo

Toshiba BC Series - Page 30

Toshiba BC Series
75 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
28 / 73
Copyright © 2019 Toshiba Teli Corporation, All Rights Reserved. http://www.toshiba-teli.co.jp/en/
D4296087A
Register
address
Read
Write
AC(*)
Memory
save
Default
Register name
Description
0x0021 F29C
R/W
-
0x0
DPCEnable
Sets the activation of DPC (Defective pixel correction) function.
0x0:OFF, 0x1:ON
0x0021 F2BC
0x0
DPCNumber
Sets the number of pixels to correct.
0x0 (0) 0x100 (256)
0x0040 0000
0x0
DPCValue [X
1
]
Sets the X coordinate of defective pixel (1st)
0.4M:0x0(0)0X2CF(719)
1.6M:0x0(0)0X59F(1439)
0x0040 0004
DPCValue [Y
1
]
Sets the Y coordinate of defective pixel (1st)
0.4M:0x0(0)0X21B(539)
1.6M:0x0(0)0X437(1079)
0x0040 0008
DPCValue [X
2
]
Sets the X coordinate of defective pixel (2nd)
0.4M:0x0(0)0X2CF(719)
1.6M:0x0(0)0X59F(1439)
0x0040 000C
DPCValue [Y
2
]
Sets the Y coordinate of defective pixel (2nd)
0.4M:0x0(0)0X21B(539)
1.6M:0x0(0)0X437(1079)
0x0040 07F8
DPCValue [X
255
]
Sets the X coordinate of defective pixel (255th)
0.4M:0x0(0)0X2CF(719)
1.6M:0x0(0)0X59F(1439)
0x0040 07FC
DPCValue [Y
255
]
Sets the Y coordinate of defective pixel (255th)
0.4M:0x0(0)0X21B(539)
1.6M:0x0(0)0X437(1079)
0x0021 F31C
R/W
-
0x0
SS Enable
Sets the activation of Sequential Shutter (SS) function.
0x0:OFF,0x1:ON
0x0021 F33C
R/W
-
0x1
SS TerminateAt
Sets the number of Tables to repeat the sequence.
Min:0x1(1),Max:0x10(16)
0x0050 0040
R/W
-
0x1
SS Entry 0
Sets the UserSet number to register to the first sequence.
Min:0x1(1),Max:0xF(15)
0x0050 0044
SS Entry 1
0x0050 0048
SS Entry 2
0x0050 004C
SS Entry 3
0x0050 0078
SS Entry 15
* 0.4M : BC040M, 1.6M : BC160M
* For registers other than those mentioned above, please refer to the IIDC2 Digital Camera Control
Specification Ver.1.0.0.
*AC: In relation to Acquisition Command (address:0x002 0303C) : If [AC] marked “”, the register is set to
following procedure.
Stop image output (0x0) → register setting / write command → Start image output (0x08)
R/W Read / Write possible
R.O. Read Only
W.O. Write Only
N.A. Not available

Related product manuals