What causes network or touch panel display to be disabled after LDAP search on Toshiba E-STUDIO 3500C All in One Printer?
If the network or touch panel display is disabled after an LDAP search on your Toshiba All in One Printer, ensure that the LDAP server is running correctly. Also, double-check that you've entered the correct LDAP settings, especially re-enter the correct password carefully because it displays with asterisks.
Why does paper jamming occur frequently in my Toshiba All in One Printer?
Frequent paper jams in your Toshiba All in One Printer could be due to several reasons. First, check if the paper size setting on the control panel matches the paper in the drawer or bypass tray. If the paper exceeds the indicated line inside the side guide, remove some sheets. Ensure there's an appropriate space between the side guide and the paper, placing the paper straight along the side guide. If the cause is not listed above, follow the guidance shown on the touch panel to locate and remove the jammed paper.
How to fix image trouble on Toshiba All in One Printer?
To address image trouble on your Toshiba All in One Printer, ensure the Automatic Document Feeder or Platen Cover is fully lowered to block outside light. Clean the original glass, platen sheet, scanning area, and guides if dirty. If the copy density is too dark, lighten it in manual mode or switch to automatic copy density mode. For highly transparent originals, place a blank sheet of paper over the original. Make sure there is contact between the original and the glass. Verify that the size and direction of the copy paper and the original, or the reproduction ratio, are set correctly. Also, clean the scanning area, guides, main charger, and slit glass.
What to do if Toshiba E-STUDIO 3500C image density is too low?
If the image density is too low on your Toshiba All in One Printer, first check if the touch panel displays a message to replace the toner cartridge and replace it if needed. If not, adjust the image density using the manual density buttons or the background adjustment function.
What to do if Toshiba All in One Printer image density is too high?
If the image density is too high on your Toshiba All in One Printer, adjust the image density using the manual density buttons or the background adjustment function.
Why Toshiba E-STUDIO 3500C functions cannot be set?
If functions cannot be set on your Toshiba All in One Printer, it may be due to incompatible function combinations. Refer to the copying function combination and image quality adjustment combination matrices, and then set them again.
Why does my Toshiba All in One Printer have image trouble?
If the image on your Toshiba All in One Printer has trouble, ensure the Automatic Document Feeder or Platen Cover is fully lowered to block outside light. Clean the original glass, platen sheet, scanning area, or guides if they are dirty. If the copy density is too dark, lighten it in manual mode or switch to automatic mode. For transparent originals, place a blank sheet over them. Ensure there's full contact between the original and the glass. Replace damp copy paper with dry paper. Verify the size, direction, and reproduction ratio settings. Clean the scanning area, guides, main charger, and slit glass. If the density is uneven horizontally, clean the main charger.
What to do if functions cannot be set on Toshiba E-STUDIO 3500C?
To set functions on your Toshiba All in One Printer, see the copying function combination and image quality adjustment combination matrices, and then set them again.
Why does LDAP authentication take so long on my Toshiba E-STUDIO 3500C?
If LDAP authentication is taking a long time on your Toshiba All in One Printer, verify that the LDAP server is running correctly. Additionally, ensure that you've entered the correct LDAP settings, especially re-entering the correct password carefully because it displays with asterisks.
How to resolve 'Cannot Print To This Equipment' error on Toshiba All in One Printer?
To fix the 'Cannot Print To This Equipment' error on your Toshiba All in One Printer, ensure you set up the proper protocol and check the settings required for your printing environment. Also, make sure the TCP/IP is set up correctly and set up the NetWare server.
General| Print Speed (Black) | 35 ppm |
|---|---|
| Print Speed (Color) | 35 ppm |
| Fax Capability | Yes |
| Copy Resolution | 600 x 600 dpi |
| Duplex Printing | Yes |
| Network Connectivity | Ethernet |
| Functions | Copier, Printer, Scanner, Fax |
| Connectivity | Ethernet, USB |
| Scan Resolution | 600 dpi |
| Copy Speed (Black/Color) | 35 ppm |
| Operating System Compatibility | Windows, Mac |
To Next Page
