Toshiba E-STUDIO 3500C

Other manuals for Toshiba E-STUDIO 3500C

Manual232 pages

Network Administration Guide78 pages

Quick Start Guide90 pages

Guide346 pages

Questions and Answers

B
Bill JohnstonAug 21, 2025
What to do if Toshiba E-STUDIO 3500C display does not change when buttons are pressed?
- A
  Anne BarkerAug 21, 2025
  If the Toshiba All in One Printer display doesn't change when buttons are pressed, it might be in energy-saving mode. Press the [ENERGY SAVER / SHUTDOWN] or [START] button to exit this mode. Note that it may take a moment for the equipment to become ready. Alternatively, if the power is off due to the weekly timer, press the [START] button to turn the power back on. If using department management, ensure the correct code is entered. For user management, verify the user information is accurate. Finally, if the 'Warming up' message is displayed, wait for the equipment to finish warming up.
M
Meghan StricklandSep 3, 2025
What to do if I cannot ping my Toshiba E-STUDIO 3500C?
- E
  epatelSep 3, 2025
  If you're unable to ping your Toshiba All in One Printer, ensure you've entered the correct TCP/IP settings. Also, check the computer’s protocol settings to confirm the gateway and subnet settings are correct. Consult the networking section of your operating system documentation.
M
Michael MoralesSep 1, 2025
How to fix 'Cannot Discover Device' on my Toshiba All in One Printer?
- P
  Peter OwensSep 1, 2025
  If your Toshiba All in One Printer cannot be discovered, the issue might stem from protocol limitations on the supporting computers. To resolve this, enable the SNMP (MIB) and verify the Read Community and Read Write Community settings. Also, ensure the TCP/IP settings are correctly configured and adjust the router settings as needed. Configure the proper protocol.
N
nicole07Aug 31, 2025
How to fix Toshiba All in One Printer that does not start?
- M
  Mr. Nathan MasonAug 31, 2025
  If your Toshiba All in One Printer does not start, ensure the power cord is fully inserted into the plug until it stops. Also, make sure the cover is properly closed.
C
christina72Aug 29, 2025
Why Toshiba E-STUDIO 3500C functions cannot be set?
- C
  Carrie LaneAug 29, 2025
  If functions cannot be set on your Toshiba All in One Printer, it may be due to incompatible function combinations. Refer to the copying function combination and image quality adjustment combination matrices, and then set them again.
N
Noah PrinceAug 27, 2025
What to do if Toshiba All in One Printer image density is too high?
- M
  Melissa RichardsonAug 27, 2025
  If the image density is too high on your Toshiba All in One Printer, adjust the image density using the manual density buttons or the background adjustment function.
M
Matthew HayesAug 27, 2025
What to do if Toshiba E-STUDIO 3500C image density is too low?
- H
  hpeckAug 27, 2025
  If the image density is too low on your Toshiba All in One Printer, first check if the touch panel displays a message to replace the toner cartridge and replace it if needed. If not, adjust the image density using the manual density buttons or the background adjustment function.
M
Maria VegaAug 25, 2025
How to fix image trouble on Toshiba All in One Printer?
- A
  Alex RamosAug 25, 2025
  To address image trouble on your Toshiba All in One Printer, ensure the Automatic Document Feeder or Platen Cover is fully lowered to block outside light. Clean the original glass, platen sheet, scanning area, and guides if dirty. If the copy density is too dark, lighten it in manual mode or switch to automatic copy density mode. For highly transparent originals, place a blank sheet of paper over the original. Make sure there is contact between the original and the glass. Verify that the size and direction of the copy paper and the original, or the reproduction ratio, are set correctly. Also, clean the scanning area, guides, main charger, and slit glass.
B
Bradley RobertsAug 23, 2025
Why does paper jamming occur frequently in my Toshiba All in One Printer?
- K
  Kellie BoothAug 23, 2025
  Frequent paper jams in your Toshiba All in One Printer could be due to several reasons. First, check if the paper size setting on the control panel matches the paper in the drawer or bypass tray. If the paper exceeds the indicated line inside the side guide, remove some sheets. Ensure there's an appropriate space between the side guide and the paper, placing the paper straight along the side guide. If the cause is not listed above, follow the guidance shown on the touch panel to locate and remove the jammed paper.

Toshiba E-STUDIO 3500C Specifications

General

Print Speed (Black)	35 ppm
Print Speed (Color)	35 ppm
Fax Capability	Yes
Copy Resolution	600 x 600 dpi
Duplex Printing	Yes
Network Connectivity	Ethernet
Functions	Copier, Printer, Scanner, Fax
Connectivity	Ethernet, USB
Scan Resolution	600 dpi
Copy Speed (Black/Color)	35 ppm
Operating System Compatibility	Windows, Mac