What to do if the air intake grilles of Toshiba RAV-HM301MUT-E Air Conditioner are damaged?
If the air intake or discharge grilles of your Toshiba Air Conditioner are deformed or damaged due to dust, dirt, or scratches, fix or replace them.
Why does the Toshiba RAV-HM301MUT-E compressor not operate?
The compressor of your Toshiba Air Conditioner might not be operating due to several reasons. It could be under the control of a 3-minute protective function, in standby because the room temperature has reached the set temperature, running in timer or fan mode, or the remote controller is set to “heating” under high outside air temperature. In any of these cases, check the compressor operation.
Why is the Toshiba Air Conditioner indoor fan not operating?
The indoor fan of your Toshiba Air Conditioner may not be operating because the air conditioner is being controlled by the cool air discharge preventive function in “heating”. In this case, check the indoor fan operation.
How to fix microcomputer misdiagnosis in Toshiba RAV-HM301MUT-E due to external noise?
If outer noise or power conditions are causing microcomputer misdiagnosis in your Toshiba Air Conditioner, and you've ruled out other causes, changing the cables of the remote controller to shielded cables may help, provided there is any noise source.
What to do if there are duplicated header remote controllers in Toshiba Air Conditioner?
If you're encountering issues with duplicated header remote controllers on your Toshiba Air Conditioner, where two remote controllers are incorrectly set as the header in a double-remote controller setup, you should adjust the remote controller settings.
What to do if Toshiba RAV-HM301MUT-E has indoor unit-outdoor unit serial communication trouble?
If your Toshiba Air Conditioner is experiencing indoor unit-outdoor unit serial communication trouble, where there is serial communication trouble between indoor unit and outdoor unit, you should check the indoor / outdoor connecting wires.
What to do if Toshiba Air Conditioner has Indoor unit heat exchanger sensor (TC) trouble?
If your Toshiba Air Conditioner is experiencing indoor unit heat exchanger sensor (TC) trouble, and an open-circuit or short-circuit of the heat exchanger sensor (TC) was detected, check the heat exchanger sensor (TC).
What to do if Toshiba RAV-HM301MUT-E Air Conditioner has CPU-CPU communication trouble?
If your Toshiba Air Conditioner is experiencing CPU-CPU communication trouble between the main MCU and motor microcomputer MCU, check the indoor P.C. board.
What to do if the exterior of Toshiba Air Conditioner has peeling?
If the exterior of your Toshiba Air Conditioner has peeling or lifting coat, apply repair coating.
What to do if Toshiba RAV-HM301MUT-E has indoor unit-remote controller regular communication trouble?
If your Toshiba Air Conditioner's indoor unit-remote controller regular communication is not working and no data is received from the remote controller or network adapter, check the remote controller and network adapter.
General| Brand | Toshiba |
|---|---|
| Model | RAV-HM301MUT-E |
| Category | Air Conditioner |
| Language | English |
External views and dimensions for RAV-HM301MUT-E indoor unit.
External views and dimensions for RAV-HM401MUT-E and RAV-HM561MUT-E(TR) indoor units.
Refrigerating cycle diagrams for single and twin types of indoor units.
Block diagram of the indoor unit controller and its connections.
Details on operation modes, temperature control, and fan speed selection.
Identification of components on the indoor unit's main circuit board.
Specifications for optional connectors on the indoor P.C. board.
Overview of troubleshooting steps and required tools.
Procedures for diagnosing and resolving various operational issues.
Method for judging trouble location using lamp indications and check codes.
Troubleshooting for issues not indicated by specific check codes.
List of indoor unit check codes, their meanings, and representative trouble positions.
Flowcharts to diagnose specific indoor unit check codes.
Procedures for replacing the indoor unit's service P.C. board.
Setup procedures for the indoor unit at the installation site.
How to perform a test run using the wired remote controller.
Procedure for setting up forced defrost using the wired remote controller.
Explanation of the LED indicators on the indoor unit's P.C. board.
How to set various functions using the remote controller.
Wiring and setting procedures for controlling units with multiple remote controllers.
How to use the monitor function to check sensor data and operation status.
Setup procedures for local site configurations and external devices.
Setup and wiring for the 1:1 model connection interface.
Procedure to set the central control address number for indoor units.
Procedures for setting line, indoor unit, and group addresses.
Details on addressing and group control configurations.
Overview of single, twin, triple, and double twin system configurations.
Examples of automatic address setup for various configurations.
Manual address setting procedures using the remote controller.
Exploded views and parts list for specific indoor unit models.
To Next Page
