Trianco TRO Evolution 30 System - Quick Connector

48 pages

Save Page as PDF

To Next Page

To Previous Page

page -41

24.15.- Quick connector

To connect and disconnect the red oil intake tube to the nozzle, proceed as follows:

- Press the connector ring in the direction of the arrow, pulling on the red tube at the same

time.

PRESS

RING

TUBE

OIL

QUICK CONNECTOR

Main Page

Default Chapter2
- Table of Contents2
1 Presentation4
2 Description of Components5
3 Control Elements6
4 Installation Instructions7
- Location7
- Hydraulic Installation7
- Electrical Connection7
- Oil Installation8
- Combustion Products Exhaustion8
- Installing Adhw Storage Tank Sanit (Optional )9
- Anti-Legionella Function (with Hot Water Tank Only)9
- Installing the SRFC2/EV Underfloor Heating Kit (Optional)10
- Heating Circuit 2 (Optional)10
5 Combustion Products Exhaustion11
- Combustion Products Exhaustion and Air Intake Dual-Duct Device Ø80 / Ø100 (Typr C53)11
- Double Conduit to Coaxial Exhaustion Transformation (Only for Tro Evolution 30 System )12
- Ombustion Products Exhaustion and Air Intake Horizontally Arranged Coaxial Device Øtype Nly for Tro Evolution Ystem )13
- Combustion Products Exhaustion and Air Intake Vertically-Arranged Coaxial Device Ø80-125 (Type C33) (Only for TRO Evolution System)14
6 Filling the Installation15
7 Digital Display16
8 Temperature Selection18
- Selecting the Boiler Set Point Temperature18
- Selecting the DHW Setpoint Temperature (with Hot Water Tank Only)18
- Selecting the Underfloor Heating Flow Setpoint Temperature (with SRHFC2/ EV Kit Option)19
9 Operation19
- Functioning in "Heating Only" Mode19
- Functioning with a Sanit Hot Water Tank20
- Heating Circuit 2 Functioning (Optional)20
- Operation with an SRHFC2/EV Underfloor Heating Kit (Optional)20
10 Additional Functions21
- Pump Anti-Block Function21
- Anti-Frost Function21
- Boiler Pressure Sensor Function21
- Telephone Relay Connection21
- Room Thermostat Connection21
- Anti-Legionella Function (Optional) (with Hot Water Tank Only)22
- Keypad Block Function22
11 E20 Remote Control (Optional)23
- Functioning Without an Outdoor Sensor23
- Functioning with an External Sensor (Optional)23
- Functioning with Adhw Tank (Optional )24
- Telephone Relay Function24
12 Boiler Security Systems25
- Temperature Safety Cut-Out25
- Burner Cut-Out25
- Low Pressure Cut-Out25
13 Draining the Boiler26
14 Switching off the Boiler26
15 First Start-Up26
16 Installation Delivery26
17 Boiler Maintenance27
- Cleaning the Boiler27
- Anti-Frost Protection28
- Boiler Water Characteristics28
18 Technical Data29
19 Circulating Pump Flow Curves30
- Characteristic Curves of the Pump30
- Regulation of the Circulation Pump30
- Pressure Drop30
20 Diagrams and Measurements31
21 Electrical Connection Diagram32
22 Electrical Diagram33
23 Alarm Codes34
24 Burner35
- Assembly35
- Burner Start-Up35
- Adjusting the Combustion Conditions35
- Primary Air Adjustment36
- Combustion Line Adjustment36
- Correct Position of Electrodes36
- Oil Pressure Adjustment37
- Pipe Operation37
- Oil Supply Piping Diagrams38
- Technical Specifications38
- Operating Curves39
- Nozzles39
- Oil Flow Versus Nozzle and Pump Pressure39
- Electrical Connection Diagram40
- Quick Connector41
- Burner Control Operating Sequence42
25 Spare Parts List43
26 Failures46

Trianco TRO Evolution 30 System - Quick Connector

Table of Contents

Related product manuals