True TI1000 - User Manual

50 pages

Save Page as PDF

To Next Page

* Assembly Guide & Warranty Card Included

ALPINE RUNNER

OWNER’S MANUAL

Model# TI1000 Revision 091418

Questions and Answers

P
paulhallSep 23, 2025
What does Fault SC05: Motor Over Speed mean on my True TI1000?
- T
  tinaweberSep 23, 2025
  Fault SC05 on your True Treadmill indicates the motor is over speed. This can be caused by high belt deck friction or line voltage issues. Lubricate the treadbelt and check the AC line voltage.
R
Robyn JohnsonSep 3, 2025
What does Fault CN07: Calibration Timeout mean on my True Treadmill?
- J
  John GibbsSep 3, 2025
  Fault CN07 on your True Treadmill indicates a calibration timeout, which could be due to low AC line voltage. Try retrying the calibration and verifying the AC voltage at the outlet.
J
Jeffrey JohnsonAug 27, 2025
What does Fault CN00 mean on my True Treadmill?
- J
  Jim GloverAug 27, 2025
  If your True Treadmill shows Fault CN00: Corrupted Console Configuration, power cycle the treadmill, re-configure the console, or re-install the software/firmware. If the firmware and software versions are not compatible, re-install software/ firmware. Contact dealer or TRUE service.
R
Richard NealSep 16, 2025
What does Fault A120: Motor Controller Fault mean on my True TI1000 Treadmill?
- W
  William WilsonSep 16, 2025
  Fault A120 on your True Treadmill indicates a motor controller fault. This may be due to a loose cable connection. Check cable connections.
W
williamstammySep 22, 2025
What does Fault A127: Motor Controller Fault mean on my True Treadmill?
- T
  Timothy HoffmanSep 22, 2025
  Fault A127 on your True Treadmill indicates a motor controller fault. Try power cycling the console, checking cable connections, or running incline calibration. If the incline potentiometer value is out of range, set the incline motor to 0% grade value.
K
Kendra RodriguezSep 6, 2025
What does Fault SP03: Belt Over Accel mean on my True Treadmill?
- T
  Terri HayesSep 6, 2025
  Fault SP03 on your True Treadmill indicates the belt is over accelerating. This can occur if the user is holding the belt back or if there's high belt deck friction. Do not try to stop the belt and lubricate the treadbelt.
E
Elizabeth DrakeSep 9, 2025
What does Fault A103: Motor Controller Fault mean on my True TI1000?
- A
  ajohnsonSep 9, 2025
  Fault A103 on your True Treadmill indicates a motor controller fault. This may be due to a loose cable. Check cable connections.
R
Russell FosterSep 16, 2025
What does Fault A119: Motor Controller Fault mean on my True TI1000?
- S
  Shelly WilliamsSep 16, 2025
  Fault A119 on your True Treadmill indicates a motor controller fault. This may be due to a loose cable connection. Check cable connections.
M
Matthew ArnoldSep 23, 2025
What does Fault SC04: Motor Under Speed mean on my True TI1000?
- D
  donna34Sep 23, 2025
  Fault SC04 on your True Treadmill indicates the motor is under speed. This can be caused by high belt deck friction, high belt tension, or low line voltage. Lubricate the treadbelt and check the drive belt and walking belt tension. Also, check the AC line voltage.
L
Lori CaldwellAug 25, 2025
What to do if my True Treadmill walking belt is off center?
- D
  David HallAug 26, 2025
  If your True Treadmill walking belt is off center, it might be due to an uneven floor. Adjust the treadmill using the rear leveling feet. Also, you may need to adjust the belt tracking. See Chapter 5: Centering the Running Belt.