True TI1000 - User Manual

Questions and Answers

J
Jeffrey JohnsonAug 27, 2025
What does Fault CN00 mean on my True Treadmill?
- J
  Jim GloverAug 27, 2025
  If your True Treadmill shows Fault CN00: Corrupted Console Configuration, power cycle the treadmill, re-configure the console, or re-install the software/firmware. If the firmware and software versions are not compatible, re-install software/ firmware. Contact dealer or TRUE service.
R
Russell FosterSep 16, 2025
What does Fault A119: Motor Controller Fault mean on my True TI1000?
- S
  Shelly WilliamsSep 16, 2025
  Fault A119 on your True Treadmill indicates a motor controller fault. This may be due to a loose cable connection. Check cable connections.
H
hardingangelaAug 28, 2025
What does Fault CN01 mean on a True Treadmill?
- M
  Mrs. Kristina Williams DVMAug 28, 2025
  If your True Treadmill displays Fault CN01: Internal Fault, power cycle the treadmill, re-configure the console, or re-install the software/firmware. Contact dealer or TRUE service.
W
Wendy BautistaAug 29, 2025
What does Fault CN05 mean on my True TI1000?
- D
  Douglas BarrAug 29, 2025
  If your True Treadmill displays Fault CN05: No Lower Control, power cycle the treadmill, check the cable connection, or re-configure the console.
S
Stephen ContrerasAug 29, 2025
What does Fault CN06 mean on True TI1000?
- S
  Shannon LevyAug 29, 2025
  If your True Treadmill displays Fault CN06: Config Mismatch, power cycle the treadmill, re-configure the console, or check cable connections.
D
Dana WardSep 22, 2025
What does Fault SC06: Motor Acceleration Fault mean on my True TI1000 Treadmill?
- R
  robertchaneySep 22, 2025
  Fault SC06 on your True Treadmill indicates a motor acceleration fault. This can occur if the user is holding the belt back or if there's high belt deck friction. Do not try to stop the belt and lubricate the treadbelt.
M
Mary WagnerSep 14, 2025
What does Fault A114: Motor Over Temp mean on my True TI1000 Treadmill?
- J
  Jacob RichardsSep 14, 2025
  Fault A114 on your True Treadmill indicates the motor is over temperature. This can be caused by high belt deck friction or low line voltage. Lubricate the treadbelt and check the AC line voltage.
G
Gina CollinsSep 12, 2025
What does Fault A110: Motor Controller Fault mean on my True TI1000?
- T
  Tammy StephensSep 12, 2025
  Fault A110 on your True Treadmill indicates a motor controller fault. This may be due to line voltage. Check AC line voltage.
C
cassandraboydAug 31, 2025
What to do if my True TI1000 heart rate is displaying erratically or not displaying?
- W
  walkerandrewAug 31, 2025
  If the heart rate on your True Treadmill is displaying erratically or not at all, there could be several reasons: * Ensure the transmitter belt contacts are making good contact with your skin and are moist. * Adjust your position to be within 3 feet (1 meter) of the console. * Replace the transmitter belt if the battery is depleted. Also, another user wearing a compatible transmitter strap may be interfering if they are within 3 feet (1 meter) of the unit. Environmental interference from high voltage power lines can also cause this issue; try moving the unit or the source of interference. If the source is plugged into the same outlet, move it to another outlet.
L
Lisa AlvarezAug 31, 2025
What does Fault CN00: Corrupted Console Configuration mean on my True TI1000 Treadmill?
- D
  Daniel SmithAug 31, 2025
  Fault CN00 on your True Treadmill indicates a corrupted console configuration, possibly due to corrupt software or incompatible firmware and software versions. Try power cycling the console. You may also need to re-configure the console or re-install the software/firmware.