xii Series 3080 Electrostatic Classifiers
Figures
S-1 Location of Warning and Information Labels .......................166Hxvi
1-1 Model 3080 Electrostatic Classifier shown with
Model 3081 Long DMA and Model 3085 Nano DMA............1-
167H1
2-1 Bottom View of Electrostatic Classifier Showing Location
of Rubber Feet. Feet can be removed to provide mounting
points on cabinet. Dimensions are in inches [mm]..............2-
168H3
2-2 Installation of Model 3077A/3077 Kr-85 Neutralizer ..........2-
169H5
2-3 Model 3077A/3077 Kr-85 Neutralizer Installed
(showing pop-up-flag indicator) ..........................................2-
170H6
2-4 Impactor Inlet ....................................................................2-
171H7
2-5 Impactor Inlet Installed on Classifier ..................................2-
172H8
2-6 Installing Long DMA in Mounting Bracket. Push down
and toward cabinet until spring locks in place. ................2-
173H10
2-7 Releasing the Long DMA Base Bracket ............................. 2-
174H10
2-8 Installing the Long DMA Side-Support Bracket.................2-
175H11
2-9 Tubing Configuration for the Model 3081 Long DMA ........2-
176H12
2-10 Installing Nano DMA in Mounting Bracket. Push down
and toward cabinet until spring locks in place. ................2-
177H13
2-11 Releasing the Nano DMA Base Bracket.............................2-
178H14
2-12 Tubing Configuration for the Model 3085 Nano DMA in
Single Blower Mode ..........................................................2-
179H15
2-13 Tubing Configuration for the Model 3085 Nano DMA in
Dual Blower Mode ............................................................ 2-
180H16
3-1 Front of the Model 3080 Electrostatic Classifier .................3-
181H1
3-2 Classifier LCD Display........................................................3-
182H2
3-3 Back Panel and Side Panel of the Model 3080
Electrostatic Classifier........................................................3-
183H4
3-4 24V DC Power Input Pin Designations................................3-
184H4
3-5 Main Internal Components.................................................3-
185H7
3-6 Schematic Diagram of the Classifier ...................................3-
186H8
4-1 Model 3081 Long Differential Mobility Analyzer ..................4-
187H2
4-2 Schematic Diagram of Long DMA .......................................4-
188H3
4-3 3085 Nano Differential Mobility Analyzer............................4-
189H4
4-4 Schematic Diagram of the Model 3085 Nano DMA..............4-
190H5
5-1 Classifier LCD Display........................................................5-
191H2
6-1 Cleaning the Impactor........................................................6-
192H2
6-2 Unscrew Middle Flange to Split Long DMA for Cleaning......6-
193H3
6-3 Cleaning/Replacing Model 3081 Dacron Screen .................6-
194H6
6-4 Disassembly of Model 3085 Nano DMA for Cleaning...........6-
195H7
6-5 Location of Ground Wire ....................................................6-
196H9
6-6 Replacing/Cleaning the Dacron Screen ............................6-
197H10
6-7 Removal of Model 3077A/3077 Kr-85 Neutralizer.............6-
198H12
6-8 Replacing Classifier Filters ...............................................6-
199H13
6-9 Location of Main PC-Board...............................................6-
200H15
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
To Next Page
Loading...
