8
PowerSeries - PC1616/PC1808/PC1832/PC1864
Re-activate Stay/Away Zones:
Press [][1] when the system is armed in the Stay mode to change the armed status to Away mode. The system will add the Stay/Away zones back into
the system after the exit delay time expires.
[][2] Trouble Display
Refer to Appendix B – Troubleshooting Guide for assistance and a detailed description of all trouble conditions.
Press [9] to acknowledge and override all existing troubles. Pressing [9] allows the panel to be armed, and will generate and log an override
event. A General System Supervisory caused by a hardwired or wireless zone expander cannot be overridden by this method. If Section [701]
option 3 is ON arming will be inhibited if a system low battery or AC trouble is detected and cannot be overridden by this method.
Press [8] in the trouble menu on any new PowerSeries keypad to enter the time and date programming menu. This option will be available if
a Loss of Clock trouble is present on the system.
[][3] Alarm Memory Display
The Memory light will be ON if an alarm occurred during the last armed period. Press [][3]. The Memory light will flash and the keypad will display
the zones that went into alarm.
: To clear the Memory light, arm then disarm the system.
[][4] – Door Chime Enable/Disable
Press [][4]. The keypad will emit 3 rapid beeps if the door chime feature is now enabled and a steady 2-second tone if it is now disabled. The same
function can be performed by pressing and holding the Chime function button for 2 seconds.
[][5] – Program User Codes
The following table identifies available user codes:
Programming User Codes
LED Keypad:
Press [][5] followed by the Master Code. The Program light will flash. The keypad will turn ON the corresponding zone lights to indicate if any user codes are
programmed. To add or change a user code, enter the 2-digit user code to be programmed. The zone light will flash. Enter a new 4 or 6-digit user code or press
[] to delete the user code. After the user code is programmed or deleted, the zone light corresponding to the user code will stop flashing. To add or change
another user code, enter the 2-digit user code to be programmed or press [#] to exit.
LCD Keypad:
Press [][5] followed by the Master Code. The keypad will display the first user (user 01) and include the letter ‘P’ in the bottom, right corner if the user
code is programmed. Scroll to the appropriate user and press the [] key to program the user (or enter the 2-digit user number). Enter a new 4 or 6-digit
user code or press [] to delete the user code. After the user code is programmed or deleted, scroll to another user or press [#] to exit.
Programming Partition Assignment
Press [][5] followed by the Master Code or Supervisor Code. Press [98] followed by the 2-digit user to change to the partition assignment. The keypad
will turn ON the corresponding zone light to indicate which partition(s) the user is assigned to. For example, if zone light 1 is ON, the user is assigned to
partition 1. To change the partition assignment, press the number corresponding to the partition. Once the correct partitions are assigned to the user, press
[#] to exit. To change the partition assignment for another user, press [98] followed by the 2-digit user number. When finished, press [#] to exit.
Programming User Attributes
Press [][5] followed by the Master Code or Supervisor Code. Press [99] followed by the 2-digit user to change to the user attributes. The keypad will
turn ON the corresponding zone light to indicate which attributes are assigned to the user.
Light [1] User can enter User Code Programming section with this code
Light [2] Duress Reporting Code is sent whenever this code is entered
Light [3] User can manually bypass zones
Light [4] User can access the Escort5580 module remotely
Light [5] For Future Use
Light [6] For Future Use
Light [7] The panel will squawk the bell output when the user arms/disarms
Light [8] One-time use code – Can disarm the system once per day and is reset at midnight.
To change the user attributes, press the number corresponding to the attribute. Once the correct attributes are assigned to the user, press [#] to exit. To
change the user attributes for another user, press [99] followed by the 2-digit user number. When finished, press [#] to exit.
[][6] – User Functions
Code
Type Function
[01]-[39], [41]-[95]
General User Codes arm, disarm
[40]
Master Code all functions
To Next Page
Loading...
