85
PARTS
Circular Knife Spindle Assembly
CIRCULAR KNIFE SPINDLE ASSEMBLY Item 10 Item 11
Size
Assembly
Item 5 Item 6 Item 7 SLICING KNIFE STRIPPER
of Cut
Number
Knife Spacer Feed Disc HOLDER PLATE
inch mm Qty. No. & Qty. Qty. No. & Slot Spacing No. & Slot Spacing
†† 3/32 (2.4) 13640 **65 13634 64 — 13632 3/32" 13633 3/32"
1/8 (3.2) 13676 49 16120 48 — 13016 1/8" § 13316 1/8"
5/32 (4.0) 13562 39 37066 39 — 13017 5/32" § 13586 5/32"
3/16 (4.8) 13410 33 16182 32 — 13018 3/16" 13024 3/16"
1/4 (6.4) 13411 25 16105 24 — 13016 1/8" 13025 1/4"
5/16 (7.9) 13412 20 16108 19 — 13017 5/32" 13026 5/16"
3/8 (9.5) 13413 17 16106 16 — 13016 1/8" 13027 3/8"
7/16 (11.1) 13414 14 37067 14 — 13148 7/16" 13028 7/16"
1/2 (12.7) 13415 13 16107 12 —
13016 1/8"
13029 1/2"
13022 1/2"
9/16 (14.3) 13428 12
16104 10 —
13018 3/16" 13137 9/16"
*16106 1 —
.600 (15.2) 13416 11 16241 10 — 13180 .600" 13021 .600"
5/8 (15.9) 13429 11
16121 9 —
13016 1/8" 13030 5/8"
*16106 1 —
3/4 (19.1) 13417 9 16109 8 — 13016 1/8" 13027 3/8"
† 3/4 (19.1) 13430 9 16106 16 8 13016 1/8" 13027 3/8"
7/8 (22.2) 13418 8
16118 6 —
13016 1/8" 13023 7/8"
*16109 1 —
1 (25.4) 13419 7 16110 6 — 13016 1/8" 13029 1/2"
† 1 (25.4) 13431 7 16107 12 6 13016 1/8" 13029 1/2"
1-1/4 (31.8) 13098 6
16111 4 —
13016 1/8" 13025 1/4"
*16110 1 —
1-1/2 (38.1) 13420 5 16112 4 — 13016 1/8" 13029 1/2"
† 1-1/2 (38.1) 13432 5 16109 8 4 13016 1/8" 13029 1/2"
2 (50.8) 13421 4 16027 3 — 13016 1/8" 13029 1/2"
3 (76.2) 13422 3 16028 2 — 13016 1/8" 13029 1/2"
†† Use 2–10043 Hex Head Cap Screws (5/16-18 x 1/2") in place of 2–10044 Hex Head Cap Screws (5/16-18 x
5/8") for attaching stripper plate (see page 77).
** Use knife 13638 (special thin knife).
† With feed disc.
* Last spacer to be placed on spindle.
§ Nickel plated manganese aluminum bronze.
To Next Page