ViewSonic PJD5133 User Manual

1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “ Option > Lamp Setting ” menu.
 Dispose the used lamp according to local regulations.
 Ensure that screws are tightened properly. Screws not tightened fully may
result in injury or accidents.
 Since the lamp is made of glass, do not drop the unit and do not scratch the
glass.
 Do not reuse the old lamp. This could cause the lamp to explode.
 Be sure to turn off the projector and unplug the AC power cord before
replacing the lamp.
 Do not use the projector with the lamp cover removed.
35

ViewSonic PJD5133 Specifications

General

Matrix size	0.55 \
Number of colors	16.78 million colors
Native aspect ratio	4:3
Projection distance	1.2 - 10 m
Vertical scan range	50 - 120 Hz
Projection technology	DLP
Supported aspect ratios	4:3, 16:9, 16:10
Contrast ratio (typical)	2000:1
Screen size compatibility	27 - 300 \
Projector native resolution	SVGA (800x600)
Keystone correction, vertical	± 40 °
Power LED	Yes
Audio input	1
Aspect ratio	16:10
Compatibility	PC, Mac
Dimensions (WxDxH)	284 x 234 x 82 mm
Connectivity technology	Wired
Focus	Manual
Optical zoom	1.1 x
Focal length range	- mm
Lamp power	180 W
Lamps quantity	1 lamp(s)
Light source type	Lamp
Service life of light source	5000 h
Service life of light source (economic mode)	6000 h
DVI port	No
Audio (L/R) in	0
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC 3.58, NTSC 4.43, NTSC M, PAL, PAL 60, PAL B, PAL D, PAL G, PAL H, PAL I, PAL M, PAL N, SECAM, SECAM B, SECAM D, SECAM G, SECAM K1, SECAM L
Supported graphics resolutions	800 x 600 (SVGA)
RMS rated power	2 W
Product type	Standard throw projector
Product color	Black
Market positioning	Presentation
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	235 W
Noise level	32 dB
Certification	CB, CCC, PSB, C-tick, KC, SASO, CE, GOST-R, Ukr, ErP, SVHC list & REACH DoC, UL, FCC (including ICES-003), cUL/CSA, Argen, NOM
Noise level (economic mode)	30 dB
Storage temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 80 %
Cables included	AC, VGA
Sustainability certificates	RoHS

Weight and Dimensions

Depth	234 mm
Width	284 mm
Height	82 mm
Weight	2600 g
Package weight	3400 g