To Next PageTo Next PageHow to fix ViewSonic Projector that does not turn on?
If your ViewSonic Projector is not turning on, first ensure the power cord is securely plugged into both the projector's AC inlet and a functioning power outlet, and that the outlet switch is on, if applicable. Also, if the projector was recently turned off, it may be in a cooling process. Wait for this process to complete before attempting to turn it on again.
Why is there no picture on my ViewSonic Projector?
If you're not seeing a picture on your ViewSonic Projector, there are several things to check: * Ensure that your video source is turned on and correctly connected. * Verify the projector is properly connected to the input signal device. * Select the correct input signal using the SOURCE key on the projector or remote. * Make sure the lens cover is open.
What to do if ViewSonic PJD5111 Projector remote control does not work?
If the remote control isn't working with your ViewSonic Projector, try these steps: 1. Replace the battery with a new one. 2. Make sure there's nothing blocking the path between the remote and the projector. 3. Ensure you are within 8 meters (26 feet) of the projector.
How to fix a blurred image on a ViewSonic PJD5111 Projector?
If the image from your ViewSonic Projector is blurred, try the following: * Adjust the focus of the lens using the focus ring. * Adjust the projection angle, direction, and height of the projector to properly align it with the screen. * Ensure the lens cover is open.
General| Projection distance | 1.5/6 m |
|---|---|
| Vertical scan range | 50 - 87 Hz |
| Horizontal scan range | 30 - 70 kHz |
| Projection technology | DLP |
| Contrast ratio (typical) | 2800:1 |
| Screen size compatibility | 35/155 \ |
| Projector native resolution | SVGA (800x600) |
| Keystone correction, horizontal | 40 ° |
| Digital zoom | 1.1 x |
| Focal length range | 21 - 23 mm |
| I/O ports | 1 × RCA jack 1 × 4-pin mini-DIN % × 15-pin mini D-sub(RGB) |
| Audio input | 1 × 3.5 mm mini jack |
| Aspect ratio | 4:3, 16:9 |
| RS-232 ports | 1 |
| Dimensions (WxDxH) | 264 x 225 x 96.4 mm |
| Power requirements | AC100–240V, 2.9 A, 50/60 Hz |
| Lamp power | 189 W |
| Light source type | Lamp |
| Service life of light source | 3000 h |
| RMS rated power | 5 W |
| Serial interface type | RS-232 |
| VGA (D-Sub) ports quantity | 5 |
| Certification | CB, ROHS, WEEE, UL/cUL, FCC-B, ICES-003, IRAM (Argentina), NOMPSB, C-tick, EK, CE, TUV/GS, GOST-R, Hygienic, SASO UKrSEPRO, CCC |
| Power consumption (typical) | 242 W |
| Operating temperature (T-T) | 0 - 40 °C |
| Operating relative humidity (H-H) | 10 - 90 % |
| Market positioning | Presentation |
Weight and Dimensions| Weight | 2300 g |
|---|
Essential safety guidelines to prevent hazards during projector use and installation.
Details the function of each button on the projector and remote control.
Instructions for connecting PCs, notebooks, and external monitors via VGA.
Details connecting Component, S-Video, and composite video sources, plus audio.
Steps for powering on the projector and initial setup.
Setting, changing, recalling, and disabling the projector's password protection.
Procedures for cleaning the projector lens and case.
Information on tracking lamp usage and understanding replacement warnings.
Detailed steps for replacing the lamp and resetting the lamp timer.
