EasyManuals Logo

Vivitek DS262 User Manual

Vivitek DS262
69 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #7 background imageLoading...
Page #7 background image
5
Attention for handing
Do not touch the lamp until it has cooled completely, because the lamp is very
hot during operation and immediately after turned off.
The lamp has to be fixed firmly to the base or socket.
Turn off the power supply during maintenance.
Do not hold the lamp except outer surface of the reflector.
Wear protective gloves and eyeglasses when handling the lamp.
Any unusual shock or vibration to the lamp should be avoided.
The lamp contains the mercury. Its breakage might cause mercury to flow out of
the reflector. Please manage provision at the customer’s product.
Do not pull the lead wire and plug by more than 24.5N.
Please be careful of handling the lamp because it is made of glass.
Please notice for keeping or handling the lamp, because there is a projection of
this lamp with reflector ahead.
Do not touch the bulb and the mirror area of the reflector.
Attention for use
Do not close or cover the lamp with any flammable stuff.
During operation, the lamp is under extremely high pressure. Please manage
provision at the customers product to prevent fragments of bulb and mercury
from flowing out of it. If the lamp bursts in case of an emergency, the sound will
be occurred.
Lamp operation should be with the specified lamp driver and the system only.
Do not look at the lamp directly during operations.
Do not expose your skin directly. We recommend to you to put on something for
protection for your skin. For example, long sleeve shirt, gloves, glassed and so
on.
Do not modify the lamp and never use a lamp that has been modified.
Any unusual shock or vibration to the lamp should be avoided during operation.
Do not use any broken lamps.
Dispose of used lamps according to your local instruction.
Do not turn on the lamp while the system is opened.
The lamp contains mercury. If the lamp bursts during operation ventilate the area
sufficiently to avoid inhaling harmful mercury fumes.
Use the lead below 200 to prevent a deterioration of cladding clad of the
fluorocarbon resin.
The lead wire insulation clad shouldnt touch the reflector.
Exchange the lamp that has already passed the life time immediately.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Vivitek DS262 and is the answer not in the manual?

Vivitek DS262 Specifications

General IconGeneral
Native aspect ratio4:3
Projection distance1.6 - 11.3 m
Projection technologyDLP
Contrast ratio (typical)15000:1
Screen size compatibility40 - 240 \
Projector native resolutionSVGA (800x600)
Keystone correction, vertical-40 - 40 °
Offset105.7 %
Throw ratio1.94 - 2.32:1
Focal length range21.8 - 25.6 mm
Aperture range (F-F)2.46 - 2.66
DVI portNo
HDMI version1.4
AC (power) inYes
Serial interface typeRS-232
USB 2.0 ports quantity0
S-Video inputs quantity1
Component video (YPbPr/YCbCr) in-
Power sourceAC
AC input voltage100 - 240 V
AC input frequency50 - 60 Hz
Power consumption (standby)0.5 W
Power consumption (typical)240 W
Power consumption (economy mode)203 W
Light source typeLamp
Service life of light source5000 h
Service life of light source (economic mode)7000 h
RMS rated power2 W
Noise level31 dB
Noise level (economic mode)28 dB
Cables includedAC, VGA
PlacementDesktop
Product typeStandard throw projector
Product colorWhite
Supported graphics resolutions800 x 600 (SVGA), 1920 x 1200 (WUXGA)
Weight and Dimensions IconWeight and Dimensions
Depth243 mm
Width332 mm
Height107 mm
Weight2600 g

Related product manuals