Wacker Neuson ET16

S-2 BA ET16 de* 1.0 * et16en1_0SIX.fm
Index
7-13
Hydraulic oil types ................................................ 7-12
Hydraulic quickhitch ............................................. 5-30
Picking up an attachment ................................ 5-31
Setting down an attachment ............................ 5-35
Hydraulic swivel unit brake ................................... 5-15
Hydraulic system .................................................. 7-37
I
Immobiliser ........................................................... 5-53
Inadmissible work procedures .............................. 5-46
Increasing the width of the stabilizer blade .......... 5-18
Indicator lights and warning lights (overview) ....... 4-28
Information and regulations on use ........................ 3-4
Information before putting into operation .............. 4-30
Information labels ................................................. 3-13
Information on this Operator’s Manual ................... 1-1
Information regarding operation with bio-hydraulic oil ..
7-13
Installing/removing the shatter protection ............. 4-21
Introduction ............................................................. 3-1
ISO/SAE control ................................................... 5-15
J
Job site shatter protection ........................... 4-20, 5-23
L
Labels ..................................................................... 3-5
Lehnhoff mechanical quickhitch system (optional) 5-25
Letting the engine warm up .................................. 4-36
Lift capacity table ......................................... 9-17, 9-20
Lifting gear applications ........................................ 5-55
Lights ...................................................................... 5-9
Loading ................................................................... 6-3
Loading material ................................................... 5-50
Loading the machine .............................................. 6-3
Loading vehicles ................................................... 5-50
Load-retaining function
......................................... 5-39
Locking the upper carriage ..................................... 6-8
Low-load operation ............................................... 4-40
Lubrication ............................................................ 7-24
Lubrication plan ...................................................... 7-9
M
Machine overview ................................................... 3-1
Machine preservation ........................................... 7-46
Machine travel ........................................................ 5-4
Machine travel and stopping .................................. 5-4
Machine travel on slopes ........................................ 5-5
Machine travel position ........................................... 5-4
Machine weight .................................................... 9-13
Main fuse box ......................................................... 9-5
Maintenance (responsibilities and prerequisites) ... 7-1
Maintenance accesses ......................................... 7-14
Maintenance of attachments ................................ 7-46
Maintenance of the electrical system ................... 7-41
Maintenance plan ................................................... 7-4
Maintenance schedule of Lehnhoff mechanical quickh-
itch system .............................................................. 7-7
Malfunctions ........................................................... 8-1
Malfunctions of the hydraulic system ...................... 8-2
Manual throttle ........................................................ 5-1
Maximum speed ..................................................... 9-3
Mechanical brake ................................................... 5-3
Mechanical quickhitch
Picking up an attachment ................................ 5-26
Setting down an attachment ............................ 5-28
Models and trade names ................................. 3-2, 9-1
N
Noise emissions ..................................................... 9-8
O
Opening the engine cover .................................... 7-15
Operation ................................................................ 5-1
Operation checklist ............................................... 4-32
Operation in water
................................................ 5-48
Operation near the sea ......................................... 5-48
Operator seat .......................................................... 4-7
Backrest adjustment .......................................... 4-8
Horizontal adjustment ........................................ 4-8
Weight adjustment ............................................. 4-7
Options ................................................................. 5-53
Overview of cabin operator's controls .................. 4-24
Overview of control elements ............................... 4-23
P
Parking checklist ................................................... 4-32
Parking the machine ............................................... 5-8
Parking the machine on slopes .............................. 5-8
Permanently putting out of operation .................... 5-57
Power outlet .......................................................... 4-22
Preheating ............................................................ 4-28
Preparations for starting the engine ..................... 4-34
Preparatory work for putting into operation .......... 4-30
Preparing lubrication ............................................... 7-8
Proportional controls ............................................. 5-52
Protective FOPS structure .................................... 4-16
Protective structures ............................................. 4-15
Putting back into operation ................................... 5-56
Putting into operation .............................................. 4-1
Putting into operation for the first time and running-in
period .................................................................... 4-33
Putting out of operation temporarily ...................... 5-55
R
Reducing the width of the stabilizer blade ............ 5-18
Reducing track tension ......................................... 7-45
Re-equipping ........................................................ 5-43
Refueling ..................................................... 7-25, 7-26
Releasing pressure ............................................... 5-43
Releasing the pressure in the operating hydraulics .....