Wacker Neuson RD 7 Series

Wacker Neuson RD 7 Series

168 pages

To Next Page

To Next Page

Loading...

5000185489 17 0911

Operator’s Manual

Roller

RD 7

Notice d’Emploi

Rouleau

5000185489

Table of Contents

Questions and Answers:

E
Ernest HoganAug 2, 2025
How to troubleshoot Wacker Neuson Industrial Equipment when the engine does not start?
- N
  Nathan JonesAug 2, 2025
  If your Wacker Neuson Industrial Equipment's engine isn't starting, there are several potential causes. First, check if the fuel tank is empty and, if so, drain the tank, change the fuel filter, and refill with fresh fuel. Also, the fuel filter may be restricted or plugged, in which case you should replace it. Check the engine oil level and activate the mechanical oil pressure monitor in case of oil pressure loss. Finally, check for loose or corroded battery connections, or a dead battery (RD 7H-ES).
T
Terry MelendezAug 17, 2025
Why is there no vibration in my Wacker Neuson RD 7 Industrial Equipment?
- L
  Leonard BensonAug 18, 2025
  If your Wacker Neuson Industrial Equipment isn't vibrating, several components could be the cause. A valve could be damaged. The exciter assembly might be damaged. The exciter motor coupling could be damaged or broken. The exciter motor might be damaged. The pump could be damaged.

Wacker Neuson RD 7 Series Specifications

General

Brand	Wacker Neuson
Model	RD 7 Series
Category	Industrial Equipment
Language	English

Summary

EC Declaration of Conformity

Safety Information

Signal Words Used in this Manual

Explains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal word meanings.

Machine Description and Intended Use

Operating Safety

Covers safe operating practices, operator qualifications, and PPE.

Operator Safety While Using Internal Combustion Engines

Focuses on hazards and safety during engine operation and fueling.

Service Safety

Outlines safety precautions for machine maintenance and repair.

Lifting and Transporting

Lifting

Instructions and precautions for safely lifting the machine using a sling or chain.

Transporting

Steps for securing the machine to a trailer for transportation.

Operation

Controls and Service Locations

Identifies and describes the machine's controls and service points.

Position of the Operator

Refueling the Machine

Procedure and safety warnings for refueling the machine.

Before Starting

Starting the Machine (RD 7 H, RD 7 H-S)

Step-by-step guide for starting the engine on specific models.

Starting the Machine (RD 7 H-ES)

Step-by-step guide for starting the engine on RD 7H-ES model.

Cold Weather Starting (RD 7 H, RD 7 H-S)

Procedure for starting the engine in cold weather conditions.

Stopping the Machine

Procedure for safely stopping the engine and machine.

Direction and Speed Control

How to control the machine's travel direction and speed.

Exciter

Parking Brake

Machine Stability

Factors affecting machine stability and how to maintain it.

Operation on Slopes

Safety precautions for operating the machine on inclines.

Rollovers

Emergency Shutdown Procedure

Steps for emergency shutdown of the machine.

Maintenance

Maintenance Schedule

Checking Engine Oil

Changing Engine Oil and Oil Filter

Step-by-step guide to changing the engine oil and filter.

Fuel System

Engine Air Filter

Checking and Adjusting Valve Clearances

Engine Cooling System

Scraper Bars

Hydraulic Oil Requirements

Hydraulic Oil Level

Changing Hydraulic Fluid and Filter

Steps for changing hydraulic fluid and filter.

Direction Lever Adjustment

Troubleshooting

Technical Data

Engine

Roller

Lubrication

Prepare for Safe Operation

Start Safely

Work Safely

Park and Shut Down Safely

Load and Unload Machine Safely

Transporting Safely

Perform Maintenance Safely

Schematics

Hydraulic Schematic

Hydraulic Schematic Components

Hydraulic Diagram

Hydraulic Diagram Components

RD 7 H ES-Electrical Schematic

RD 7 H-ES-Electrical Schematic Components

Related product manuals

Wacker Neuson RD 7H

Preview: Wacker Neuson ET12 02

Wacker Neuson ET12 02