How to fix an iced up air motor on WAGNER EvoMotion 5-125?
If the air motor of your WAGNER Water Pump is iced up, it's likely due to excessive condensation water in the air supply. To resolve this, install a water separator.
How to fix iced up air motor in WAGNER EvoMotion 5-125 Water Pump?
If the air motor of your WAGNER Water Pump is iced up, it's likely due to excessive condensation water in the air supply. To resolve this, install a water separator.
What to do if my WAGNER EvoMotion 5-125 Water Pump does not work?
If your WAGNER Water Pump isn't working, several issues could be the cause. It could be due to the air motor not functioning; in this case, try opening and closing the ball valve on the pressure regulator or briefly disconnecting the compressed air supply. Another reason could be a defective air pressure regulator, indicated by no pressure on the gauge; try briefly disconnecting the compressed air or repairing/changing the regulator. Also, ensure you have sufficient compressed air supply and that the fluid section or high-pressure hose isn't blocked—clean the fluid section or replace the hose if needed. If the pump stops at a switching point, press the starter on the reversing valve to restart it and clean/lubricate the slide on the reversing valve.
Why is my WAGNER Water Pump spray jet with irregular pressure?
If you're experiencing irregular operation or pulsating spray jet with your WAGNER Water Pump, several factors could be responsible. The viscosity of the material might be too high, requiring dilution. Alternatively, the valves could be clogged, necessitating cleaning, possibly with a cleaning agent. Check for any foreign bodies in the suction valve by dismantling the suction valve housing and cleaning the valve seat. Also, ensure the compressed air line isn't too small. Other potential issues include worn valves, packings, or pistons (replace them), a clogged control or work air filter (check and clean), a clogged suction filter (clean it), or a stuck ball in the suction or piston valve (clean with cleaning agent).
What to do if WAGNER EvoMotion 5-125 runs when discharge duct is closed?
If your WAGNER Water Pump continues to run even when the discharge duct is closed, it typically indicates that the packings, valves, or pistons are worn out and need replacement.
What to do if WAGNER Water Pump has irregular operation and spray jet collapses?
If the WAGNER Water Pump has irregular operation and the spray jet collapses, it could be due to several factors. The viscosity of the spraying product might be too high, in which case you should thin it. The valves could be clogged, requiring you to clean the pump, potentially soaking it in a cleaning agent. A foreign body might be in the suction valve, necessitating dismantling the suction valve housing and cleaning the valve seat. Other potential causes include a compressed air line that is too small, worn-out valves, packings, or pistons that need replacement, a clogged control or work air filter that needs cleaning, a clogged suction filter that also needs cleaning, or a ball in the suction or piston valve that is stuck, requiring cleaning with a cleaning agent.
What happens if WAGNER EvoMotion 5-125 runs when the discharge duct is closed?
If the WAGNER Water Pump runs when the discharge duct is closed, it is likely that the packings, valves, or pistons are worn out and need to be replaced.
Why WAGNER EvoMotion 5-125 does not work?
The WAGNER Water Pump may not work due to several reasons. It might not start or may stop because of issues with the ball valve on the pressure regulator. Try opening and closing the ball valve or briefly disconnecting the compressed air supply. There could also be no pressure indication on the pressure gauge because of a defective air pressure regulator; in this case, disconnect the compressed air supply briefly or repair/change the pressure regulator. Check for an insufficient supply of compressed air, or clogs in the fluid section or high-pressure hose, which would require dismounting and cleaning the fluid section or replacing the high-pressure hose. Also, if the pump stops at a switching point, press the starter on the reversing valve to restart it, and clean the slide on the reversin...
General| Max Pressure | 5 bar |
|---|---|
| Power Consumption | 1200 W |
| Voltage | 230 V |
| Frequency | 50 Hz |
| Power | 1200 W |
| Max Flow Rate | 5400 l/h |
To Next Page
