Wayne Helix 4000 - Page 5

Table of Contents
WU017834 Rev. 05 July 2023 Wayne Fueling Systems | Dover Fueling Solutions 5
5.4 PRIMING SUCTION PUMPS (SUCTION DISPENSERS) .............................................................. 46
5.5 BLEEDING PRODUCT LINES (REMOTE DISPENSERS) ............................................................. 46
5.6 AUTHORIZING THE DISPENSER VIA STANDALONE MODE........................................................ 46
5.7 INITIAL DELIVERY ................................................................................................................ 47
5.8 METER CALIBRATION - WAYNE IMETER
™
OR XFLO
®
FUEL METERS ....................................... 48
5.8.1 During the Accuracy Verification and Calibration Procedures .................................... 48
5.8.2 Accuracy Verification Procedure - iMeter or Xflo ........................................................ 48
5.8.3 Meter Calibration Procedure - iMeter or Xflo............................................................... 49
5.9 TEST EMERGENCY SHEAR VALVES ...................................................................................... 50
5.10 NOZZLE BOOT SWITCH CHECK .......................................................................................... 50
5.11 ANNUNCIATOR OPERATION CHECK .................................................................................... 50
5.12 TEST THE 12-BUTTON PRESET KEYPAD............................................................................. 50
5.13 PAYMENT PLATFORM CONFIGURATION (OPTIONAL)............................................................. 51
5.14 WAYNE DISPENSER SECURE ACCESS................................................................................ 51
5.15 AUDIT REPORTING DISPLAY MODE (WEIGHTS & MEASURES).............................................. 51
5.16 SECURITY PRECAUTIONS................................................................................................... 52
5.16.1 Disable Standalone Mode Operation ........................................................................ 52
5.16.2 Change iGEM Passwords ......................................................................................... 52
5.17 BALANCE VAPOR RECOVERY SYSTEM INSTALLATION REQUIREMENTS ................................. 53
5.17.1 Dynamic Back Pressure Testing ............................................................................... 53
5.17.1.1 Back Pressure System Check List ...................................................................... 53
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1 SAFETY PRECAUTIONS ........................................................................................................ 55
6.2 BASIC DISPENSER REQUIREMENTS ...................................................................................... 55
6.3 OPERATING THE DISPENSER ............................................................................................... 55
6.4 RESTARTING AFTER POWER FAILURE OR SHUTDOWN .......................................................... 56
6.5 CYCLING POWER TO CLEAR FAULTS.................................................................................... 56
6.6 ERROR CODES ................................................................................................................... 57
6.7 ELECTRONIC TOTALIZER READINGS ..................................................................................... 58
6.7.1 Totalizer Readings by Hose (Product) Position .......................................................... 58
6.7.2 Totalizer Volume Readings by Meter Position ............................................................ 59
6.7.3 Electro-Mechanical Totalizer Operation ...................................................................... 59
6.8 STAND-ALONE OPERATION.................................................................................................. 60
6.9 S
ERIAL MODE - POS AUTHORIZES DISPENSER .................................................................... 61
6.9.1 Recovering from Standalone Jumper Fail-safe........................................................... 62
6.10 SMART SECURE ACCESS (SSA)........................................................................................ 63
6.10.1 Arming or Disarming Smart Secure Access (SSA) Using a OneShot Password ...... 64
6.10.2 Arming or Disarming Smart Secure Access (SSA) Using Maintenance Mode ......... 65
7 MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.1 HOW TO GET SERVICE ON YOUR DISPENSER....................................................................... 67
7.2 P
REVENTATIVE MAINTENANCE ............................................................................................. 67
7.3 D
ISPENSER CLEANING......................................................................................................... 68
7.4 M
ETER MAINTENANCE......................................................................................................... 70
7.5 H
OSE AND HOSE RETRACTOR ............................................................................................. 70
7.6 FILTER / STRAINER - REMOTE ............................................................................................. 71
7.7 F
ILTER / STRAINER - SUCTION ............................................................................................. 72
7.8 PRINTER MAINTENANCE - DW-14 RS-232 PRINTER............................................................. 73