Webasto SVS300 - Page 47

To Next Page

To Previous Page

SVS-200 Installation, Operation and Maintenance

IMPORTANT INFORMATION – SAVE THESE INSTRUCTIONS

20153-W-03-01 41 Webasto Charging Systems, Inc.

To install output cable(s):

1. Install output cable(s) ensuring mounting screws and lock washers are properly installed and

tightened. Recommended torque: 8.47 Nm (75 in-lbs)

2. Proper Cable management system is required to relieve stress concentration from output

connector mounting hardware areas

Note: 1) Do not remove connector key(s) from Connector

2) Minimum bend radii (3.5 inch) are required for output cables

Main Page

Table of Contents4
Getting Started7
Safety Precautions - Read before Using8
Symbol Usage8
Technical Support10
ESD Precautions10
Non-Standardtools10
System Description11
Figure 3- 1 Components of the Charging System11
Installation12
Preparation12
Wiring13
General Guidelines13
Ground Wire13
Charging Cables / Cable Management System13
Chassis Ground13
Grounding13
Hardware13
Physical Installation14
Figure 4- 1 SVS-300 Installation15
Connecting AC (Utility) Power16
Figure 4- 2 Bolt Pattern for SVS-300 Installation16
Table 4-1 Utility and Wiring Information17
Table 4-2 Output Characteristics for SVS-30017
Figure 4- 3 AC Input Terminal Block18
Figure 4- 4 Location of Chassis Ground Connector18
Operation19
Start up19
Language Selection19
Figure 5- 1 Language Selection Screens19
Charging20
Figure 5- 2 Connecting Status Screens20
Figure 5- 3 Front Panel Layout20
Table 5- 1 LED Labels and Meanings21
Figure 5- 4 Charge Complete Screens21
Equalization22
Viewing Charge Data Screens22
Figure 5- 5 Charging Data Screens23
Fault and Warning Screens24
Figure 5- 6 Fault or Warning Screens24
Charge Event Log25
Figure 5- 7 Fault/Warning Log Data Screens25
Figure 5- 8 Charge Event Log Data Screens27
Data Logs, Configuration, and Advanced Programming Features28
Figure 5- 9 Top Menu Items for the Advanced Features28
Programming Menus29
Charger Configuration30
Figure 5- 10 Programming Menu Entry30
Figure 5- 11 Charger Configuration Options32
Clear Backup Memory33
External Light Configuration33
Figure 5- 12 Clear Backup Memory Menu33
Figure 5- 13 External Light Configuration Menu34
EQ Button Action35
Figure 5- 14 EQ Button Action35
Auto EQ36
Fast Charge SOC Limit36
Figure 5- 15 Auto EQ Menu36
Figure 5- 16 Fast Charge SOC Limit Screens36
Full Charge Feature Configuration37
Reduced Rate Charge Feature Configuration38
Figure 5- 17 Full Charge Setup Screens38
Temperature Readout Selection39
Figure 5- 18 Reduced Charge Rate Setup Screens39
Ventilation System40
Figure 5- 19 Temperature Readout Selection Screens40
Figure 5- 20 Ventilation System Setup40
Air Circulation Control41
Watering System41
Figure 5- 21 Air Circulation Control Setup41
Figure 5- 22 Watering System Standard Screens42
Charger ID43
Date and Time43
Figure 5- 23 Charger ID Screens43
Charge Time Control44
Figure 5- 24 Date and Time Setting Menus44
Figure 5- 25 Charger Time Control Menu44
Output Format Selection Menu45
Figure 5- 26 Output Format Selection Menu45
Maintenance46
General Maintenance46
Figure 6- 1 DC Output Connections46
External Interface Specifications (Diagnostic Port)48
Figure 6- 2 Diagnostic Port Pinout48
Table 6- 1 Fault Codes49
Technical Specifications50
Table 6- 2 Warning Codes50

Webasto SVS300 - Page 47

Table of Contents

Related product manuals