Why does my Worx WR206E (Landroid Vision) vibrate?
Your Worx Landroid Vision lawn mower may vibrate because the blade disc is unbalanced, possibly due to damaged blades. Inspect the blades, replace them if necessary, and clear any debris or foreign objects from the blades and blade disc.
What to do if my Worx WR206E Lawn Mower does not charge?
If your Worx Lawn Mower isn't charging, check that the power cord is properly connected to the charger and the charger is connected to a working power supply. Also, ensure that both charging strips on the mower touch the center of the charging contacts on the charging pile.
Why does my Worx WR206E have shorter run-times?
Shorter run times for your Worx Lawn Mower can be caused by several factors. Check the blade disc for clogs and clean it, especially if the grass is high or thick. Examine the blade disc and blades for debris and replace them if necessary, as an unbalanced disc can increase power consumption. The battery might also be old and need replacement, or the working time may need to be reset.
Why Worx WR206E Lawn Mower cannot correctly dock with the charging pile?
If your Worx Lawn Mower isn't docking correctly, try restarting it, as environmental factors may be interfering. Also, clean the contact pins on the charging pile and the charging strip on the mower with a cloth to ensure good connection.
What to do if Worx WR206E software upgrade fails?
If the software upgrade fails on your Worx Lawn Mower, move closer to the router to strengthen the Wi-Fi signal. Also, ensure that the battery level is above 50% by placing the mower on the charging station.
What to do if Worx WR206E Lawn Mower flips over?
If your Worx Lawn Mower flips over, exclude any inclined obstacles from its working area.
Why does my Worx WR206E Lawn Mower stop in the working area?
If your Worx Lawn Mower stops in the working area, remove any obstacles. If the cutting height is set too low for the grass length or the grass is too dense, raise the cutting height and then gradually lower it.
How to fix LED light on Worx Lawn Mower charging pile?
If the LED light on the charging pile of your Worx Lawn Mower doesn't turn on, check that the charging base is properly connected to the charger and the charger is connected to a suitable power supply.
Why Worx WR206E secondary area is not mowed?
If the secondary area isn't being mowed by your Worx Lawn Mower, ensure the RFIDs are installed and reprogrammed correctly. Remove any obstacles between the RFIDs in the pathway. Also, make sure there is no boundary curved within 1.5 m range of the boundary wire for the RFID.
How to set the correct time on Worx Lawn Mower?
If your Worx Lawn Mower isn't operating at the correct time, ensure the clock is set correctly. Also, check and correct the programmed cutting times. If using the app, verify that the percentage of weekly operating time is set correctly.
General| Type | Robotic lawn mower |
|---|---|
| Bluetooth | Yes |
| Noise level | 59 dB |
| Display type | LCD |
| Cutting width | 180 mm |
| Product color | Black, Orange, Red, Silver |
| Cutting system | Rotary blades |
| Number of blades | 3 |
| Number of wheels | 3 wheel(s) |
| Maximum lawn area | 600 m² |
| Mulching function | - |
| Maximum cutting height | 60 mm |
| Minimum cutting height | 30 mm |
| Suitable for slope up to | 30 % |
| International Protection (IP) code | IPX5 |
| Battery type | Built-in battery |
| Power source | Battery |
| Battery capacity | 2 Ah |
Weight and Dimensions| Depth | 626 mm |
|---|---|
| Width | 460 mm |
| Height | 265 mm |
| Weight | 13500 g |
To Next Page
