20 Buy Online! Wurtec.com Buy Online! Wurtec.com 21
Testing the Phone Line (cont.)
STEP 1
Press
TALK
/ END
key on the keypad.
STEP 2
If you do not have a valid telephone line the phone will say “invalid telephone line”.
At this point you will need to trouble shoot the telephone line or call the telephone
service provider. If your phone line is valid, the phone will say “Enter number to
be dialed” and you should hear a standard dial tone. At this point you can dial the
emergency number to verify it works or you can press
TALK
/ END
to hang up the phone.
Phone Line Volume
STEP 1
Be sure the phone is connected to a live telephone line and has either external
power connected or a 9V battery. If you have both the external power and a 9V
battery connected be sure the battery is rechargeable, or it could result in a battery
malfunction.
STEP 2
To INCREASE the volume of the person you are speaking to rst press the
TALK
/ END
key. If you have a live telephone line, the phone will say “Please enter number to
be dialed” and then you will hear a standard dial tone. DO NOT dial a number.
Once you hear the dial tone, Press the
TALK
/ END
and
VOL UP
keys at the exact same time
and then release. You will hear a number and your dial tone increase in volume.
Continue to press the
TALK
/ END
and
VOL UP
keys at the same time and then release until
the desired volume is reached. The phone will say “8” once the maximum volume
is reached. When nished press
TALK
/ END
to hang up the phone.
STEP 3
To DECREASE the volume of the person you are speaking to rst press the
TALK
/ END
key. If you have a live telephone line, the phone will say “Please enter number to
be dialed” and then you will hear a standard dial tone. DO NOT dial a number.
Once you hear the dial tone, Press the
TALK
/ END
and
#
VOL DN
keys at the exact same time
and then release. You will hear a number and your dial tone decrease in volume.
Continue to press the
TALK
/ END
and
#
VOL DN
keys at the same time and then release until
the desired volume is reached. The phone will say “one” once the lowest volume is
reached. When nished press
TALK
/ END
to hang up the phone
Flowchart
Note: This ow chart is for programming the phone with the onboard keypad. When calling
into the phone to program you can use this ow chart as well, but you will have the added
step of pressing
2
to enter program mode once the phone answers.
Troubleshooting
If you have any questions about the installation or operation of your S3 Communicator, please
call us toll free at (800) 837-1066, 8:00 am—5:00 pm, Monday-Friday. You can also call our
direct Tech Line at 419-930-1066.
Keypad Not Working
If you are programming before you connect the phone in the elevator be sure you have
a fresh 9V battery connected to the phone. The 9V battery energizes the keypad when
programming outside of the elevator. CAUTION when connecting the phone to external
power be sure the 9V battery is rechargeable, otherwise you could damage the phone.
1-To Program
2-To Review
Push Program Menu
Button on Keypad
1-First Number
2-Second Number
3-Third Number
1-Announcements On/Off
2-Immediate Two-Way Conversation On/Off
3-Call Cancellation On/Off
4-Timing Out On/Off
5-Maintenance Announcement On/Off
1-To Program
2-To Review
3-To Delete
1-To Program
2-To Review
3-To Delete
1-To Program
2-To Review
3-To Delete
1-To Program
2-To Review
1-To Program
2-To Review
1-Site ID
2-Announcements
1-First Announcement
2-Second Announcement
3-Third Announcement
Program Status
Main Menu
1-Phone Numbers 2-Messages 3-Advanced Options 4-Program Status 5-Ring Time *0-Disconnect
Advanced Options
1-User Preferences 2-Talk Time 3-Access Code 4-Touch Tone ID 5-Ring Count 6-Unit # 7-External Output
1-To Program
2-To Review
3-To Delete
To Next Page
Loading...