12 Buy Online! Wurtec.com Buy Online! Wurtec.com 13
Programming (Locally or Remotely) | Advanced Options
User Preferences - Immediate Two-Way Conversation On/O
This feature allows the persons in the car to speak immediately with the called party after the
emergency call is answered. NOTE: If Immediate Two-Way Conversation is enabled the
Site ID message will not play.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
1
for user preferences.
STEP 4
Press
2
for immediate two-way conversation.
STEP 5
Once in the immediate two-way conversation menu, you can press
1
to turn on
immediate two-way conversation. Press
2
to review whether immediate two-way
conversation is on or o (immediate two-way conversation is o by default). Press
3
to turn o immediate two-way conversation. Press
#
VOL DN
to return to the previous
menu to continue on programming. Or press
VOL UP
then
0
to exit programming
mode once you are nished.
User Preferences - Call Cancellation On/O
When Call Cancellation is ON, the voice prompt states “Press button again to cancel” as soon
as a call is made. Pressing the button again will abort the call.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
1
for user preferences.
STEP 4
Press
3
for call cancellation.
STEP 5
Once in the call cancellation menu, you can press
1
to turn on call cancellation.
Press
2
to review whether call cancellation is on or o (by default call cancellation
is o). Press
3
to turn o call cancellation. Press
#
VOL DN
to return to the previous
menu to continue programming. Press
VOL UP
then
0
to exit programming when
nished.
Programming (Locally or Remotely)
STEP 3
To program the in car announcements press
2
. The phone will then ask you to
press
1
for rst announcement,
2
for second announcement, or
3
for third
announcement. These announcements coincide with the emergency numbers
programmed into the phone. The message itself is played inside the elevator. For
example, if the phone is set to dial 911, you may record “calling police station.” To
program an announcement for the rst number press
1
then press
1
again to
record. The phone will say “at the tone record your message followed by
#
VOL DN
.
STEP 4
If the message is correct you can press
#
VOL DN
to return to the previous programming
menu, you can follow the steps again to record your new message over the old
message, or you can press
VOL UP
then
0
to exit program mode.
Note: The recorded announcement should not exceed 6 seconds.
Programming (Locally or Remotely) | Advanced Options
In this group of menus, you will have the option to choose user preferences, set talk time,
enter an access code, enter touch tone ID, set ring count and review program status.
User Preferences - Announcements On/O
Announcements are used to notify persons in the car which of the possible three emergency
phone numbers are being dialed. Use these at your discretion. Turning o announcement will
also turn o the Site ID message inside the elevator cab. The Site ID will, however, still play
for the operator.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
1
for user preferences.
STEP 4
Press
1
for announcements menu.
STEP 5
Once in the announcements menu you can press
1
to turn on the
announcements. Press
2
to review whether announcements are on or o.
Press
3
to turn o announcements. Press
#
VOL DN
to return to the previous menu to
continue programming. Or press
VOL UP
then
0
to disconnect.
To Next Page
Loading...