14 Buy Online! Wurtec.com Buy Online! Wurtec.com 15
Programming (Locally or Remotely) | Advanced Options
User Preferences - Maintenance Announcements On/O
When Maintenance Announcements are ON voice prompts are enabled for: external power
failure, battery failure, and telephone line failure. If there are any failures, you’ll hear them
announced in the car: “External power failure” or “Battery failure” or “Telephone line failure.”
The message is played every 5 minutes for external power and battery failure until xed. The
message for telephone line failure will play for the rst time after 30 minutes and then every 5
minutes thereafter until it is xed.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
1
for user preferences.
STEP 4
Press
5
for maintenance announcements.
STEP 5
Once in the maintenance announcements menu, you can press
1
to turn
on maintenance announcements. Press
2
to review whether maintenance
announcements are on or o (maintenance announcements are o by default).
Press
#
VOL DN
to return to the previous menu to continue programming. Press
VOL UP
then
0
to exit programming mode once you are nished.
User Preferences - Timing Out
When Timing Out is ON, fteen (15) seconds before the end of time specied by talk time (see
page 15 for an expalanation of this feature) the phone will prompt “Timing out, press
1
to
avoid disconnection”. When Timing Out if OFF, the phone will stay on the line until the called
party hangs up.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
1
for user preferences.
STEP 4
Press
4
for timing out.
STEP 5
Once in the timing out menu, you can press
1
to enable timing out. Press
2
to
review whether timing out is on or o. Press
3
to disable timing out. Press
VOL UP
then
0
to exit programming mode once you are nished.
Programming (Locally or Remotely) | Advanced Options
Talk Time
Talk Time is the period of time allowed for two-way conversations. Fifteen (15) seconds
before the end of the time period the voice prompt will say “Timing out. Press
1
to avoid
disconnection” on the operator end. Enter a number between 30 and 999 seconds. Factory
set default is 180 seconds.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
2
for talk time.
STEP 4
To program a dierent talk time than the default 180 seconds (3 minutes) press
1
STEP 5
The phone will say “enter a number between 30 and 999 followed by
#
VOL DN
. The
number you enter is in seconds. For example, if you press 45, that would be 45
seconds.
STEP 6
If you have entered the desired talk time correctly you can press
#
VOL DN
to return to
the previous menu to continue with programming, you can repeat the steps again to
re-enter a dierent number to overwrite the previous one, or you can press
VOL UP
then
0
to exit programming if you are nished.
Access Code
This code enables password protection for programming from a remote location. Enter up to
eight (8) digits. Factory set default is none.
STEP 1
Press
PROG
MENU
button on the keypad.
STEP 2
Press
3
for advanced options.
STEP 3
Press
3
for Access Code.
STEP 4
Press
1
to program an access code. Press
2
to review what the already
programmed access code is (by default there is no access code). You can press
3
to erase the access code altogether.
STEP 5
Press
#
VOL DN
to return to the previous menu and continue on programming. If you are
nished programming you can press
VOL UP
then
0
to exit program mode.
To Next Page
Loading...
