Wurtec S3 Communicator - Programming Ring-Down Line; Programming Ring Time; Programming Messages (Site ID); Programming Messages (Announcements)

10 Buy Online! Wurtec.com Buy Online! Wurtec.com 11
Programming (Locally or Remotely)
STEP 5 Press
1
to program the number you want the phone to autodial. The phone will
ask you to “Enter number followed by
#
VOL DN
. Enter the number and press the
#
VOL DN
key. The phone will recite the number programmed. If the number is correct you
can continue on to programming by pressing
#
VOL DN
to return to the previous menu.
If you are nished programming the number you can press
VOL UP
then
0
to leave
programming mode.
Programming Ring-Down Line
STEP 1 Press
PROG
MENU
button on the keypad.
STEP 2 Press
1
for phone numbers.
STEP 3 Press
1
for rst emergency number.
STEP 4 Press
1
to program rst emergency number. The phone will say “enter number
followed by
#
VOL DN
. Since there is no number to dial on a ring-down line, program a
VOL UP
for the number, then press
#
VOL DN
. The phone will then say “You entered star”.
STEP 5 At this point you can press
#
VOL DN
to return to the previous menu and continue with
programming or you can press
VOL UP
then
0
to exit program mode.
Programming Ring Time
Ring Time allows you to program how long the rst emergency number is dialed. By default,
the rst emergency number will dial for 45 seconds. This can be programmed from 30 to 99
seconds depending on elevator code and or preference. Note: 2009 elevator code states a
45 second default ring time. Pre-2009 code states a 30 second default ring time. Please
be sure to program accordingly.
STEP 1 Press
PROG
MENU
button on the keypad.
STEP 2 Press
5
for Ring Time.
STEP 3 Press
1
to program Ring Time. Press
2
to review.
STEP 4 The phone will ask you to enter a number between 30 and 99 followed by the
#
VOL DN
Once you have entered your choice, the phone will repeat the number back to
you. If correct press
#
VOL DN
to return to the previous menu or
VOL UP
then
0
to exit
programming.
Programming (Locally or Remotely)
Programming Messages (Site ID)
Follow the steps below to program the Site ID message and local announcements. The Site
ID must identify where the emergency call is coming from. It’s played every time a call is
placed to or from the S3C, if not in immediate two-way. It is very important that this message
be recorded, as this is normally the way the call can be traced without verbal communication
from the passenger.
DEFAULT SETTING: The Site ID message will play inside the elevator cab. This can be
turned o󰀨 in the Announcements Menu. (see page 12)
STEP 1 Press
PROG
MENU
button.
STEP 2 Press
2
for message menu.
STEP 3 Press
1
if you want to program the site identication message. Press
2
if you
want to program for in car announcements. Press
#
VOL DN
to return the previous menu.
Or
VOL UP
then
0
to exit program mode.
STEP 4 To program the site identication message press
1
. The phone says “at the
tone, record your message followed by
#
VOL DN
. At the tone, record the message and
then press
#
VOL DN
. If the message is correct you can press
#
VOL DN
to get to the previous
menu and continue programming, if you made a mistake and need to record again,
simply follow the steps again and it will automatically record over the old message.
If you are nished programming press
VOL UP
then
0
to exit program mode.
Programming Messages (Announcements)
There are three in car local announcements that notify the trapped person which of the 3
possible emergency numbers are being dialed. Each message can be up to 6 seconds long
and can typically contain the number that is being dialed or the name of the location the
number is dialing. For example, if the rst number was programmed to dial 911, you may
record ‘Calling 911’ or ‘Calling Police’.
STEP 1 Press
PROG
MENU
button.
STEP 2 Press
2
for message menu. (continued on the next page)