Wyrestorm EX-SW-0301-H2 - 4 Switch Configuration; Configuring a Static IP Address; Configuring Video; Configuring RX Output Resolution

© Copyright 2018 WyreStorm Technologies | WyreStorm.com
EX-SW-0301-H2 API | 180619-1616
5 of 13
North America: 844.280.WYRE (9973) | UK/EMEA: +44 (0) 1793 230 343
Email: Support@WyreStorm.com
4. Switch Configuration
4.1 Configuring a Static IP Address
By default, the switcher is set to a static IP of 192.168.11.043. We recommend changing this as it shared with other WyreStorm
products and may cause improper communication if left unchanged. Connect to the RX via RS-232 and send the following
command to set the IP address.
Set Static IP Address
SET IPADDR STATIC ip4addr [IP Address] netmask [Netmask]<CR><LF>
Example: SET IPADDR STATIC ip4addr 192.168.11.243 netmask 255.255.255.0 <CR><LF>
Response: IPADDR STATIC ip4addr 192.168.11.243 netmask 255.255.255.0 <CR><LF>
Query IP Address
GET IPADDR<CR><LF>
Response: IPADDR STATIC ip4addr xx.xx.xx.xx netmask xx.xx.xx.xx <CR><LF>
Example: GET IPADDR<CR><LF>
Response: IPADDR STATIC ip4addr 192.168.11.243 netmask 255.255.255.0 <CR><LF>
Note: This command can only be sent to the receivers (RX) RS-232 port.
4.2 Configuring Video
Configuring RX Output Resolution
By default, the RX is set to Auto Scale to the resolution of the connected display. However, this can be configured to suit the
installation.
Set Output Resolution
SET RES all [Resolution] rx<CR><LF>
Example:
SET RES all Fix:1920x1200@60 rx<CR><LF>
Response:
RES SET all Fix:1920x1200@60 rx<CR><LF>
[Resolution]=
AutoScaler
Fix:1024x768@60
Fix:1280x720@60
Fix:1280x800@60
Fix:1280x1024@60
Fix:1920x1080@60
Fix:1920x1200@60
Fix:3840x2160@30
Fix:3840x2160@60
Query Output Resolution
GET RES_OUT all rx<CR><LF>
Example:
GET RES_OUT all rx<CR><LF>
Response:
RES GET all Fix:1920x1200@60 rx<CR><LF>
AutoScaler
Fix:1024x768@60
Fix:1280x720@60
Fix:1280x800@60
Fix:1280x1024@60
Fix:1920x1080@60
Fix:1920x1200@60
Fix:3840x2160@30
Fix:3840x2160@60
Auto:[Resolution] | Resolution=Scaled resolution based of connected display
Configuring Input EDIDs
By default, all inputs are set to an EDID of 1920x1080@60Hz 2CH. However, this can be configured to suit the installation.
Set Input EDID
SET EDID [Input] [Resolution]<CR><LF>
Example:
SET EDID hdmi_tx 1920x1080@60Hz<CR><LF>
Response:
EDID SET hdmi_tx 1920x1080@60Hz<CR><LF>
Query Input EDID
GET EDID [Input]<CR><LF>
Example: GET EDID hdmi_tx<CR><LF>
Response
EDID GET hdmi_tx 1920x1080@60Hz <CR><LF>
[Input]=hdmi_tx | dp_tx | vga_tx | hdbt_rx | hdmi_rx
[Resolution]=
3840x2160@30Hz/1920x1200@60Hz
1920x1080@60Hz
1680x1050@60Hz
1600x900@60Hz
1440x900@60Hz
1360x768@60Hz
1280x720@60Hz
1024x768@60Hz