Wyrestorm EX-SW-0301-H2 - Enable;Disable HDCP Support; Query Current HDCP Support Level; Configuring Device Switching; Default Device (TX;RX)

© Copyright 2018 WyreStorm Technologies | WyreStorm.com
EX-SW-0301-H2 API | 180619-1616
6 of 13
North America: 844.280.WYRE (9973) | UK/EMEA: +44 (0) 1793 230 343
Email: Support@WyreStorm.com
Enable/Disable HDCP Support
Set HDCP Support On/Off
SET HDCP_S [Input] [Prm]<CR><LF>
Response: HDCP_S SET [Input] [Prm]<CR><LF>
Example: SET HDCP_S hdmi_tx on<CR><LF>
Response: HDCP_S SET hdmi_tx on<CR><LF>
Query HDCP Support On/Off Status
GET HDCP_S [Input]<CR><LF>
Response: HDCP_S GET [Input] [Prm]<CR><LF>
Example: GET HDCP_S hdmi_tx<CR><LF>
Response: HDCP_S GET hdmi_tx on <CR><LF>
[Input]= hdmi_tx | hdbt_rx | hdmi_rx
[Prm]=on | off
Query Current HDCP Support Level
GET HDCP_IN [Input]<CR><LF>
Response: GET HDCP_IN GET [Input] [Prm]<CR><LF>
Example: SET HDCP_S hdmi_tx<CR><LF>
Response: HDCP_IN GET hdmi_tx hdcp1.4 tx<CR><LF>
[Input]= hdmi_tx | dp_tx | vga_tx | hdbt_rx | hdmi_rx
[Prm]= hdcp1.4 | hdcp2.2 | off
4.3 Configuring Device Switching
Default Device (TX/RX)
Set Default Device
SET DEFDEVICE [Device]<CR><LF>
Response: DEFDEVICE SET [Device]<CR><LF>
Example: SET DEFDEVICE tx<CR><LF>
Response: DEFDEVICE SET tx<CR><LF>
Query Default Device
GET DEFDEVICE<CR><LF>
Response: DEFDEVICE GET [Device]<CR><LF>
Example: GET DEFDEVICE<CR><LF>
Response: DEFDEVICE GET tx<CR><LF>
[Device] = tx | rx
Auto Switch Mode
Enable/Disable Auto Switch Mode
SET AUTOSW_FN [Prm] [Device]<CR><LF>
Response: AUTOSW_FN SET [Prm] [Device]<CR><LF>
Example: SET AUTOSW_FN on tx<CR><LF>
Response: AUTOSW_FN SET on tx<CR><LF>
Query Auto Switch Mode Status
GET AUTOSW_FN [Device]<CR><LF>
Response: AUTOSW_FN GET [Prm] [Device]<CR><LF>
Example: SET AUTOSW_FN on tx<CR><LF>
Response: AUTOSW_FN SET on tx<CR><LF>
[Prm] = on | off
[Device] = tx | rx | all
4.4 Configuring Relays
Relay Power
SET RELAY_PWR [Prm] rx<CR><LF>
Response: RELAY_PWR SET [Prm] rx<CR><LF>
Example: SET RELAY_PWR on rx<CR><LF>
Response: RELAY_PWR SET on rx<CR><LF>
[Prm] = on | off
Relay mode
Set Relay Mode
SET RELAY_M [Prm] rx <CR><LF>
Response: RELAY_M SET [Prm] [Device]<CR><LF>
Example: SET RELAY_M latch rx<CR><LF>
Response: RELAY_M SET latch rx<CR><LF>
Query Relay Mode
GET RELAY_M rx<CR><LF>
Response: RELAY_M GET [Prm] [Device]<CR><LF>
Example: GET RELAY_M rx<CR><LF>
Response: RELAY_M GET latch rx<CR><LF>
[Prm] = latch | momentary