Xvent WiIND Series - Atacama Heating Unit Wiring Diagram; Details of Connecting the Main Terminal Box to the Regulator ELEMENTAIR-E-M1 and with the Accessories; Connection of the Wind Curtain with the Regulator ELEMENTAIR-E-M1

29 pages

Save Page as PDF

To Next Page

To Previous Page

Verze 1

–

GBR

(

.202

)

502

5. Atacama heating unit wiring diagram

5.1. Details of connecting the main terminal box to the regulator ELEMENTAIR-E-M1 and with the

accessories

5.2. Connection of the Wind curtain with the regulator ELEMENTAIR-E-M1

Main Page

Table of Contents2
General Information4
Introduction4
Use of the Unit4
Transport, Inspection of Delivery and Storage4
Contents of the Package5
Before Start of Installation5
Technical Parameters5
WIND Air Curtain Design5
Axial Ec Fans5
Water Exchanger5
Curtain Casing5
Exhaust Lamellas5
Main Dimensions and Requirements for the Minimum Working Space for the WIND Curtain6
Technical Data7
Technical Data of Water Heaters7
Installation - Installation of Air Curtains in the Working Position8
General Information, Recommendations and Safety During Installation of the Wind Air Curtain8
Electrical Safety When Installing the Curtain8
Modification of Existing Heating Distribution Systems8
Load Bearing Capacity of the Assembly Site8
Minimum Assembly Distances8
Minimum Safety Distance from Flammable Substances9
Operation Environment of the Curtain9
Levelling of the Curtain9
Ceiling Installations9
Positioning the Curtain in the Working Position9
Fixing the Curtain to the Floor9
Vertical Installation - Curtain Chaining10
Chained Curtain Mounting10
Side Anchoring of the Chained Assembly11
Maximum Height of Chained Curtains11
Vertical Installation - Increased Barrier Effect12
Horizontal Installation12
Preparation for the Curtain Suspension12
Determination of the Installation Site13
Auxiliary Anchoring Structures13
Correct Installation in Horizontal Position13
Examples of Curtain Suspension - Horizontal Installation14
Measurement of Anchoring Holes14
Installation of the Auxiliary Anchoring Structure14
Installation - Hanging the Curtain into the Working Position14
Horizontal Installation - Curtain Chaining15
Installation of the Auxiliary Anchoring Structure15
Determination of the Installation Location for the Chained Curtains15
Auxiliary Anchoring Structures for Chained Curtains15
Correct Installation in Horizontal Position During Curtain Chaining15
Examples of Curtain Suspension - Horizontal Installation - Chaining17
Measurement of Anchoring Holes for Chained Curtains17
Installation - Suspension of the Chained Curtains into the Working Position17
Water Exchanger Connection18
Connection of the Curtain to the Hot Water Distribution System18
Venting (Discharge) Valve19
Example Hydraulic Diagram of Unit Connection19
Electrical Installation and Electrical Connection20
General Information - Safety20
Connection of Power Supply and Curtain Control20
Description of Power and Control Terminals - Electrical Diagram of Motors21
Description of Connection of 1 Curtain21
Description of the Curtain Connection During the Chaining21
Connection to the Mains22
Display of Electrical Parameters on the Curtain22
Regulation22
General Information - Safety22
Control Elements23
Atacama Heating Unit Wiring Diagram24
Details of Connecting the Main Terminal Box to the Regulator ELEMENTAIR-E-M1 and with the Accessories24
Connection of the Wind Curtain with the Regulator ELEMENTAIR-E-M124
Connection of Chained Wind Curtains with Regulator ELEMENTAIR-E-M125
Commissioning26
Before the First Start Check the Following26
Switching on26
Regular Maintenance and Cleaning of the WIND Curtain26
Regular Maintenance26
Cleaning Procedure26
Service27
Troubleshooting Procedure28
Decommissioning and Recycling28
Warranty29
Conclusion29

Xvent WiIND Series - Atacama Heating Unit Wiring Diagram; Details of Connecting the Main Terminal Box to the Regulator ELEMENTAIR-E-M1 and with the Accessories; Connection of the Wind Curtain with the Regulator ELEMENTAIR-E-M1

Table of Contents