Why does my Yamaha 85AED Outboard Motor fuel management gauge show incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition may be wrong. To resolve this, default the engine number. Then, turn the key switch on in order from the portside engine to re-memorize each engine number.
Why is the illumination not lighting on my Yamaha 85AED Outboard Motor gauge?
If the illumination isn't lighting, it could be because of a power issue or a damaged gauge. You should try replacing the fuse, ensuring the couplers are securely connected, replacing any damaged wires or hubs, or replacing the gauge.
What to do if my Yamaha 85AED Outboard Motor gauge display does not wake up?
If the gauge display doesn't wake up, it could be due to a lack of electrical power or a damaged gauge. Try these steps: replace the fuse, securely connect the couplers, replace any damaged wires or hubs, or replace the gauge itself.
How to troubleshoot Yamaha 85AED PTT relay?
If the PTT relay on your Yamaha Outboard Motor isn't working, it could be due to a short, open, or loose connection in the wiring harness; check the wiring harness for continuity. Another possibility is a PTT relay malfunction, so check the PTT relay itself.
What to do if Yamaha Outboard Motor PTT motor does not operate?
If the PTT motor on your Yamaha Outboard Motor isn't working, start by checking the battery terminal for loose connections. Also, ensure the battery isn't discharged. Inspect the fuse (20A) to see if it has blown. Then, check the PTT motor lead and ground circuit for any shorts, opens, or loose connections. Finally, if none of those are the cause, you may need to disassemble and check the PTT motor itself for a malfunction.
What to do if Yamaha 85AED Outboard Motor fuel management gauge shows incorrect fuel consumption?
If the fuel management gauge shows incorrect fuel consumption, the engine recognition might be wrong (especially for multi-applications). To fix this, default the engine number and turn the key switch on in order from the portside engine to re-memorize each engine number.
How to setup Yamaha 85AED tachometer to show the oil pressure?
Select the oil press. display.
Why Yamaha 85AED Outboard Motor boat speed and/or coolant pressure gauge does not show?
If the boat speed and/or coolant pressure gauge does not show, it is likely that the optional sensor has not been installed. Install the optional sensor.
What to do if Yamaha 85AED trim gauge always shows fully tilted up position?
If the trim gauge always shows a fully tilted-up position, the trim sender signal is not being received. Connect the pink lead connectors to each other.
What causes Yamaha 85AED Outboard Motor gauge response to be poor or down?
If the gauge response is poor or down, a market obtainable unit connected to the system may have failed, or the signal volume has exceeded 50% of the capacity. Try replacing the unit or removing the heavy signal output unit.
Step-by-step guide for safely uncrating the outboard motor from its steel frame.
Guidance on proper outboard motor mounting for optimal performance and reliability.
Guidance on selecting the appropriate propeller based on application and operating load.
Describes the tiller handle and its electrical functions, similar to side mount remote control box.
Provides a wiring diagram for the 6x4 multi-function tiller handle (US models).
Procedures for installing gauges, including location selection and stud mounting.
Essential gauge for monitoring engine speed for optimal performance and accurate operation.
Functions as fuel flow, consumption, economy gauge, and RPM synchronizer.
Provides representative wiring diagram samples for remote controls and instruments.
Illustrates wiring configurations for various engine applications (single, twin, triple).
Table outlining common system or gauge problems, their causes, measures, and notes.
Illustrates wiring configurations for single, twin, and quad engine applications with 6Y9 gauges.
Details battery capacity requirements for proper engine start-up and performance maintenance.
General| Fuel Induction System | Carburetor |
|---|---|
| Starting System | Manual |
| Ignition System | CDI |
| Max Power Output | 4.5 kW (6.1 hp) at 5500 rpm |
| Full Throttle RPM Range | 5, 000 - 6, 000 rpm |
| Gear Ratio | 2.08:1 |
| Shaft Length | S: 381 mm (15.0 in) |
To Next Page
