E
esanchezAug 28, 2025
What if the disc loaded into my Yamaha RDX-E700 Receiver is not compatible?
- JJames CastroAug 28, 2025
If the disc loaded into the Yamaha Receiver may be not compatible, make sure you use a disc supported by the DVD receiver.
To Next PageTo Next PageWhat if the disc loaded into my Yamaha RDX-E700 Receiver is not compatible?
If the disc loaded into the Yamaha Receiver may be not compatible, make sure you use a disc supported by the DVD receiver.
How to reduce noise during stereo broadcast on my Yamaha RDX-E700 Receiver?
If you are experiencing too much noise during stereo broadcast on your Yamaha Receiver, the FM antenna may be connected improperly. Make sure the FM antenna is connected properly. Also, the radio station you selected may be far away from your area or radio wave reception is weak in your area. Try Manual Tuning to increase the signal quality or use a multi-channel outdoor antenna.
How to fix Yamaha RDX-E700 Receiver remote control that doesn't work?
If your Yamaha Receiver remote control isn't working, consider these potential causes: * You may be operating the remote outside of its operational range. * The remote control sensor on the DVD receiver may be exposed to direct sunlight or certain types of lighting. * The remote control mode selection may be incorrect. * The batteries may be worn out; try replacing them.
Why doesn't the Preset Tuning function work on my Yamaha Receiver?
If the Preset Tuning function does not work on your Yamaha Receiver, the preset (memory) may have been erased. Preset radio stations again.
What to do if Yamaha playback does not start immediately when pressing play?
The disc may not be set in the disc tray properly, so set the disc in the disc tray properly. The disc may be dirty, so wipe the disc clean. The disc loaded into the DVD receiver may be not compatible, so make sure you use a disc supported by the DVD receiver. When moved the DVD receiver from a cold place to warm one, condensation may be form on the disc reading lens, so wait for one to two hours, then try again.
What to do if Yamaha preset station settings have been cleared?
If the preset station settings have been cleared, the power to the DVD receiver may have been lost for more than a week. Make sure the power cable is plugged into outlet firmly, then preset the stations again.
What to do if Yamaha remote control does not work for operating the DVD receiver?
The remote control may be operated outside the remote control operation range. The remote control sensor on the DVD receiver may be exposed to direct sunlight or lighting (inverted fluorescent lamps), so change the lighting or DVD receiver’s orientation. The remote control mode selection may be improper, so select the mode that suits your purpose. The batteries may be worn out, so replace the batteries with new ones.
Why do the speakers make no sound on my Yamaha RDX-E700?
Several factors could be at play. Check that the volume isn't set too low and that the Mute function is disabled. Also, verify you've selected the correct input source and that all cables are properly connected. If you're using a disc, ensure it's compatible with the receiver. Finally, if playing a DTS source, make a digital connection to a component with a DTS decoder and select “RAW” for “DIGITAL OUTPUT” in the OSD menu.
What to do if Yamaha RDX-E700 Receiver power turns on but immediately shuts off?
First, ensure the power cable is firmly plugged into the outlet. Next, check all speaker cables to ensure they are properly connected and not shorted. If the receiver experienced a strong electrical shock, set it to Standby, disconnect the power cable for 30 seconds, then reconnect and turn it on.
How to fix a Yamaha Receiver remote control that is not working?
If the remote control isn't operating the Yamaha Receiver, consider these possibilities: * You may be operating the remote outside of its operational range. * The remote control sensor on the receiver might be exposed to direct sunlight or certain lighting. * The remote control mode selection may be incorrect; select the appropriate mode. * The batteries might be worn out; replace them with new ones.
General| Type | Receiver |
|---|---|
| Audio Channels | 2.1 |
| Remote Control | Yes |
| Speaker Impedance | 6 ohms |
| Amplifier Type | Digital |
| Output Power | 100W per channel (6 ohms, 1kHz, 10% THD) |
Details on components requiring exact replacement due to special characteristics.
Procedure to verify proper insulation of conductive surfaces after service.
Information on laser beam emission during operation and handling precautions.
Essential steps for grounding worktables and personnel to prevent static damage.
Specific precautions for handling the high-precision DVD mechanism to avoid damage.
Technical details for the amplifier, including output power, distortion, and sensitivity.
Covers power supply, consumption, weight, dimensions, and included accessories.
Step-by-step guide for safely removing the RDX-E700's top cover.
Step-by-step guide for safely removing the RDX-E700's front panel.
Step-by-step guide for safely removing the RDX-E700's DVD mechanism.
Detailed steps to reset the DVD Mechanism Assy to factory default settings.
Part details for the RDX-E700 sub panel assembly.
Part details for the RDX-E700 power supply unit.
Part details for the RDX-E700 DVD mechanism assembly.
