YASKAWA VS MINI J7 series - Page 17

16
■ Constant Setup and Initialization - - - - - - - - - - - - - - - - - - - - - - 44
 Constant Selection/Initialization (n01) - - - - - - - - - - - - - - - - - - 44
■ Selecting V/f Pattern - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -45
 Adjusting Torque According to Application - - - - - - - - - - - - - - - 45
■ Switching LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - - - - 48
 How to Select LOCAL/REMOTE Mode - - - - - - - - - - - - - - - - - 48
■ Selecting RUN/STOP Commands - - - - - - - - - - - - - - - - - - - - -49
 LOCAL Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 49
 REMOTE Mode- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -49
 Operating (RUN/STOP Commands) Using Communications
(When Option Card is Installed) - - - - - - - - - - - - - - - - - - - - - - 50
■ Selecting Frequency Reference - - - - - - - - - - - - - - - - - - - - - - 50
 Setting by Operator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 50
■ Setting Operation Conditions - - - - - - - - - - - - - - - - - - - - - - - - 51
 Reverse Run Prohibit (n05) - - - - - - - - - - - - - - - - - - - - - - - - -51
 Multi-step Speed Selection - - - - - - - - - - - - - - - - - - - - - - - - - - 51
 Operating at Low Speed - - - - - - - - - - - - - - - - - - - - - - - - - - - - 52
 Adjusting Speed Setting Signal - - - - - - - - - - - - - - - - - - - - - - - 53
 Adjusitng Frequency Upper and Lower Limits- - - - - - - - - - - - - 54
 Using Two Acceleration/Deceleration Times - - - - - - - - - - - - - - 55
 Momentary Power Loss Ridethrough Method (n47)- - - - - - - - - 56
 S-curve Selection (n20) - - - - - - - - - - - - - - - - - - - - - - - - - - - - 56
 Torque Detection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -57
 Frequency Detection Level (n58)- - - - - - - - - - - - - - - - - - - - - - 59
 Jump Frequencies (n49 to n51)- - - - - - - - - - - - - - - - - - - - - - - 60
 Continuing Operation Using Automatic Retry Attempts (n48) - - 60
 Operating a Coasting Motor without Tripping - - - - - - - - - - - - - 61
 Holding Acceleration/Deceleration Temporarily - - - - - - - - - - - - 62
 Using Frequency Meter or Ammeter (n44) - - - - - - - - - - - - - - - 63
 Calibrating Frequency Meter or Ammeter (n45) - - - - - - - - - - -63
 Reducing Motor Noise or Leakage Current Using Carrier
Frequency Selection (n46) - - - - - - - - - - - - - - - - - - - - - - - - - -64
 Operator Stop Key Selection (n06) - - - - - - - - - - - - - - - - - - - -66