EasyManuals Logo

Yealink SIP-T46S User Manual

Yealink SIP-T46S
253 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #150 background imageLoading...
Page #150 background image
User Guide for T4 Series IP Phones
138
2. Select Enabled from the pull-down list of Allow Trans Exist Call.
3. Click Confirm to accept the change.
Performing a Blind Transfer
Procedure:
1. Press the TRANSFER key or Transfer (Trans) during a call.
2. You can do one of the following:
- Enter the number or select a contact from the placed call list you want to transfer to.
- Press Directory (Dir). Select a desired contact from the Directory list(s).
On the SIP-T48S/T48G IP phone, tap the Directory or History. Tap the desired
contact.
3. Press B Transfer (B Trans) to complete the transfer.
You can also hang up the handset or press the TRANSFER key when transferring a call by
entering number.
From the Calls screen or Transfer to screen, you can also use a Transfer key (refer to Configuring
a Transfer Key), BLF/BLF List key (refer to Configuring a BLF Key/Configuring BLF List Settings) or
Speed Dial key (refer to Placing a Call Using a Speed Dial Key) to perform blind transfer to the
pre-defined number directly. Before performing a blind transfer using these keys, make sure
that the Transfer Mode via Dsskey is configured as Blind Transfer. For more information on
how to configure it, refer to Configuring Transfer Mode via Dsskey.
Note
If the entered transferee number matches the Dial Now rule, the phone will dial out the number
by default. You can also perform blind transfer when the entered number matches the Dial Now
rule. Check with your system administrator to find out if this feature is available on your phone.
For more information on Dial Now rule, refer to Configuring the Dial Now.
Downloaded from ManualsNet.com search engine

Table of Contents

Other manuals for Yealink SIP-T46S

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yealink SIP-T46S and is the answer not in the manual?

Yealink SIP-T46S Specifications

General IconGeneral
ManualYes
Cables includedLAN (RJ-45)
Number of handles included1 pc(s)
MountingDesk/Wall
Handset typeWired handset
Product typeIP Phone
Product colorBlack
Voice codecsCNG, G.711Mu, G.711a, G.722, G.723.1, G.726, G.729ab, VAD, iLBC
Lines quantity16 lines
Phonebook capacity1000 entries
Number of VoIP accounts16
Operating temperature (T-T)-10 - 50 °C
Operating relative humidity (H-H)10 - 95 %
Display diagonal4.3 \
Display resolution480 x 272 pixels
AC adapter input voltage100 - 240 V
AC adapter output current2 A
AC adapter output voltage5 V
Dual-Tone Multi-Frequency (DTMF) modesIn-band, Out-of band, SIP info
Volume controlDigital
Number of programmable keys10
USB 2.0 ports quantity1
Ethernet LAN (RJ-45) ports2
Networking standardsIEEE 802.3af
Ethernet LAN data rates10, 100, 1000 Mbit/s
Ethernet LAN interface typeGigabit Ethernet
Supported network protocolsSIP v1, SIP v2, LLDP/CDP/DHCP, OpenVPN, IEEE802.1X, IPv6, FTP/TFTP/HTTP/HTTPS
Harmonized System (HS) code85171800
Weight and Dimensions IconWeight and Dimensions
Depth213 mm
Width244 mm
Height185 mm
Package depth255 mm
Package width274 mm
Package height128 mm

Related product manuals