YOKOGAWA DL350 - Page 115

4-88
IM DL350-17EN
:CURSor:FFT:PEAK<x>:F:VALue?
Function Queries the frequency-axis value of an FFT
cursor (peak cursor).
Syntax
:CURSor:FFT:PEAK<x>:F:VALue?
<x> = 1, 2 (cursors 1 and 2)
Example
:CURSOR:FFT:PEAK1:F:VALUE?
-> :CURSOR:FFT:PEAK1:F:
VALUE 2.0000000E+03
:CURSor:FFT:PEAK<x>:RANGe
Function Sets or queries the FFT peak cursor
measurement range.
Syntax
:CURSor:FFT:PEAK<x>:RANGe {<NRf>,
<NRf>}
:CURSor:FFT:PEAK<x>:RANGe?
<x> = 1, 2 (cursors 1 and 2)
 <NRf>=−5.00to5.00
Example
 :CURSOR:FFT:PEAK1:RANGE−5.00,5.00
:CURSOR:FFT:PEAK1:RANGE?
->:CURSOR:FFT:PEAK1:RANGE−5.00,5.00
:CURSor:FFT:PEAK<x>:Y?
Function Queries all Y-axis settings of an FFT cursor (peak
cursor).
Syntax
:CURSor:FFT:PEAK<x>:Y?
<x> = 1, 2 (cursors 1 and 2)
:CURSor:FFT:PEAK<x>:Y:STATe
Function Sets or queries whether the Y-axis value of an
FFT cursor (peak cursor) is displayed.
Syntax
:CURSor:FFT:PEAK<x>:Y:
STATe {<Boolean>}
:CURSor:FFT:PEAK<x>:Y:STATe?
<x> = 1, 2 (cursors 1 and 2)
Example
:CURSOR:FFT:PEAK2:Y:STATE ON
:CURSOR:FFT:PEAK2:Y:STATE?
-> :CURSOR:FFT:PEAK2:Y:STATE 1
:CURSor:FFT:PEAK<x>:Y:VALue?
Function Queries the Y-axis value of an FFT cursor (peak
cursor).
Syntax
:CURSor:FFT:PEAK<x>:Y:VALue?
<x> = 1, 2 (cursors 1 and 2)
Example
:CURSOR:FFT:PEAK2:Y:VALUE?
-> :CURSOR:FFT:PEAK2:Y:
VALUE 30.933333E+00
:CURSor:FFT:TYPE
Function Sets or queries the FFT cursor type.
Syntax
:CURSor:FFT:TYPE {OFF|PEAK|MARKer}
:CURSor:FFT:TYPE?
Example
:CURSOR:FFT:TYPE PEAK
:CURSOR:FFT:TYPE?
-> :CURSOR:FFT:TYPE PEAK
:CURSor[:TY]?
Function Queries all cursor settings for the T-Y waveform.
Syntax
:CURSor[:TY]?
:CURSor[:TY]:DEGRee?
Function Queries all angle cursor settings for the T-Y
waveform.
Syntax
:CURSor[:TY]:DEGRee?
:CURSor[:TY]:DEGRee:D<x>?
Function Queries all angle (D<x>) settings for the angle
cursors on the T-Y waveform.
Syntax
:CURSor:TY:DEGRee:D<x>?
<x> = 1, 2
:CURSor[:TY]:DEGRee:D<x>:STATe
Function Sets or queries whether the angle (D<x>)
between the angle cursors on the T-Y waveform
is displayed.
Syntax
:CURSor:TY:DEGRee:D<x>:
STATe {<Boolean>}
:CURSor:TY:DEGRee:D<x>:STATe?
<x> = 1, 2
Example
:CURSOR:TY:DEGREE:D1:STATE ON
:CURSOR:TY:DEGREE:D1:STATE?
-> :CURSOR:TY:DEGREE:D1:STATE 1
:CURSor[:TY]:DEGRee:D<x>:VALue?
Function Queries the angle (D<x>) between the angle
cursors on the T-Y waveform.
Syntax
:CURSor:TY:DEGRee:D<x>:VALue?
<x> = 1, 2
Example
:CURSOR:TY:DEGREE:D1:VALUE?
-> :CURSOR:TY:DEGREE:D1:
VALUE−179.55000E+00
:CURSor[:TY]:DEGRee:DD?
Function Queriesallangledifference(Δdvalue)settings.
The angle difference is between the angle cursors
on the T-Y waveform.
Syntax
:CURSor:TY:DEGRee:DD?
:CURSor[:TY]:DEGRee:DD:STATe
Function Sets or queries whether the angle difference
(Δdvalue)betweentheanglecursorsontheT-Y
waveform is displayed.
Syntax
:CURSor:TY:DEGRee:DD:
STATe {<Boolean>}
:CURSor:TY:DEGRee:DD:STATe?
Example
:CURSOR:TY:DEGREE:DD:STATE ON
:CURSOR:TY:DEGREE:DD:STATE?
-> :CURSOR:TY:DEGREE:DD:STATE 1
4.9 CURSor Group