YOKOGAWA DL350 User Manual

4-130
IM DL350-17EN
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DPRoximal?
Function Queries all distal, mesial, and proximal settings.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPROXIMAL?
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DPRoximal?
command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DPRoximal:MODE
Function Sets or queries the distal, mesial, and proximal
point mode setting.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:MODE {PERCent|
UNIT}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:MODE?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DPROXIMAL:
MODE PERCENT
:MEASURE:CHANNEL1:DPROXIMAL:MODE?
-> :MEASURE:CHANNEL1:DPROXIMAL:
MODE PERCENT
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DPRoximal:MO
DE? command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DPRoximal:PERCent
Function Sets or queries the distal, mesial, and proximal
points as percentages.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:PERCent {<NRf>,
<NRf>,<NRf>}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:PERCent?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
<NRf> = 0 to 100 (%, 0.1 steps)
The order is <Proximal><Mesial><Distal>.
Example
:MEASURE:CHANNEL1:DPROXIMAL:
PERCENT 20,50,80
:MEASURE:CHANNEL1:DPROXIMAL:PERCENT?
-> :MEASURE:CHANNEL1:DPROXIMAL:
PERCENT 20.0,50.0,80.0
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DPRoximal:PER
Cent? command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DPRoximal:UNIT
Function Sets or queries the distal, mesial, and proximal
points.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:
UNIT {<Voltage>,<Voltage>,<Voltage>|
<Current>,<Current>,<Current>|
<NRf>,<NRf>,<NRf>}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DPRoximal:UNIT?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
<Voltage><Current><NRf> = The selectable
range is the measurement range.
The order is <Proximal><Mesial><Distal>.
Selectable range of MEAS:{CHAN<x>}:DPR:UNIT
For <Voltage>,<Voltage>,<Voltage>, the
selectable range is ±the measurement range.
For Math channels: ±5 div
Example
:MEASURE:CHANNEL1:DPROXIMAL:
UNIT -10,0,10
:MEASURE:CHANNEL1:DPROXIMAL:UNIT?
-> :MEASURE:CHANNEL1:DPROXIMAL:
UNIT -10.0000E+00,0.00000E+00,
10.0000E+00
Description • For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DPRoximal:UN
IT command.
• You cannot set the distal, mesial, and proximal
points using units on frequency modules.
• Depending on the settings that were in use
before you sent this command, the values may
not be set according to the parameters.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:METHod
Function Sets or queries the modes of a set of high
and low points (rising-time and falling-time
measurement references).
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:METHod {AUTO|MAXMin}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:METHod?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:METHOD AUTO
:MEASURE:CHANNEL1:METHOD?
-> :MEASURE:CHANNEL1:METHOD AUTO
Description For channels that have sub channels, use
the :MEASure:CHANnel:SCHannel:METHod
command.
4.22 MEASure Group

YOKOGAWA DL350 Specifications

General

Brand	YOKOGAWA
Model	DL350
Category	Recording Equipment
Language	English