YOKOGAWA DL350 - Page 163

4-136
IM DL350-17EN
:MEASure:CHANnel<x1>:BIT<x2>:DELay:V
ALue?
Function Queries the delay measurement result of the
specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
VALue? {<NRf>}
<x1> = 1 to 6
<x2> = 1 to 8
<NRf> = 1 to the number of history entries (can
be omitted)
Example
:MEASURE:CHANNEL1:BIT1:DELAY:VALUE?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
VALUE 0.000000E+00
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:<Parame
ter>?
Function Queries all settings related to the waveform
parameter of the specified bit of the specified
channel on a logic module.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>?
<Parameter> = {AVGFreq|DUTYcycle|
FREQuency|PERiod|PNUMber}
:MEASure:CHANnel<x1>:BIT<x2>:<Parame
ter>:{MAXimum|MEAN|MINimum|SDEViati
on}?
Function Queries the waveform parameter statistics value
of the specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>:{MAXimum|MEAN|MINimum|
SDEViation}?
<x1> = 1 to 6
<x2> = 1 to 8
<Parameter> = {AVGFreq|DUTYcycle|
FREQuency|PERiod|PNUMber}
Example
:MEASURE:CHANNEL1:BIT1:FREQUENCY:
MEAN?
-> :MEASURE:CHANNEL1:BIT1:FREQUENCY:
MEAN 50.00000E+00
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:<Parame
ter>:COUNt?
Function Queries the waveform parameter statistics count
of the specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>:COUNt?
<x1> = 1 to 6
<x2> = 1 to 8
<Parameter> = {AVGFreq|DUTYcycle|
FREQuency|PERiod|PNUMber}
Example
:MEASURE:CHANNEL1:BIT1:FREQUENCY:
COUNT?
-> :MEASURE:CHANNEL1:BIT1:FREQUENCY:
COUNT 10
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:<Parame
ter>:STATe
Function Sets or queries the on/off state of the waveform
parameter of the specified bit of the specified
channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>:STATe {<Boolean>}
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>:STATe?
<x1> = 1 to 6
<x2> = 1 to 8
<Parameter> = {AVGFreq|DUTYcycle|
FREQuency|PERiod|PNUMber}
Example
:MEASURE:CHANNEL1:BIT1:FREQUENCY:
STATE ON
:MEASURE:CHANNEL1:BIT1:FREQUENCY:
STATE?
-> :MEASURE:CHANNEL1:BIT1:FREQUENCY:
STATE ON
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:<Parame
ter>:VALue?
Function Queries the measured waveform parameter value
of the specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
<Parameter>:VALue? {<NRf>}
<x1> = 1 to 6
<x2> = 1 to 8
<Parameter> = {AVGFreq|DUTYcycle|
FREQuency|PERiod|PNUMber}
<NRf> = 1 to the number of history entries
Example
:MEASURE:CHANNEL1:BIT1:FREQUENCY:
VALUE?
-> :MEASURE:CHANNEL1:BIT1:FREQUENCY:
VALUE 50.00000E+00
Description This command is valid on logic input channels.
4.22 MEASure Group