YOKOGAWA DL350 - Page 75

4-48
IM DL350-17EN
:CHANnel<x1>:CAN:SCHannel<x2>:UNIT
Function Sets or queries the data unit string of the
specified sub channel on a module that can
monitor CAN bus signals.
Syntax
:CHANnel<x1>:CAN:SCHannel<x2>:
UNIT {<String>}
:CHANnel<x1>:CAN:SCHannel<x2>:UNIT?
CAN Bus Monitor Module (720240) or
the CAN/CAN FD monitor module (720242)
<x1> = 1 to 4
CAN & LIN Bus Monitor Module (720241)
<x1> = 1, 3
<x2> = 1 to 60
<String> = Up to 16 characters
Example
:CHANNEL3:CAN:SCHANNEL1:UNIT "AAAA"
:CHANNEL3:CAN:SCHANNEL1:UNIT?
-> :CHANNEL3:CAN:SCHANNEL1:
UNIT "AAAA"
Description This command is valid when the data type (:CHA
Nnel<x1>:CAN:SCHannel<x2>:VTYPe) is set to
UNSigned, SIGNed, or FLOat.
:CHANnel<x1>:CAN:SCHannel<x2>:VTYPe
(Value Type)
Function Sets or queries the data type of the specified sub
channel on a module that can monitor CAN bus
signals.
Syntax
:CHANnel<x1>:CAN:SCHannel<x2>:
VTYPe {UNSigned|SIGNed|FLOat|LOGic}
:CHANnel<x1>:CAN:SCHannel<x2>:VTYPe?
CAN Bus Monitor Module (720240) or
the CAN/CAN FD monitor module (720242)
<x1> = 1 to 4
CAN & LIN Bus Monitor Module (720241)
<x1> = 1, 3
<x2> = 1 to 60
Example
:CHANNEL3:CAN:SCHANNEL1:VTYPE SIGNED
:CHANNEL3:CAN:SCHANNEL1:VTYPE?
-> :CHANNEL3:CAN:SCHANNEL1:
VTYPE SIGNED
:CHANnel<x1>:CAN:SCHannel<x2>:ZOOM
Function Sets or queries the vertical zoom factor of logic
waveforms on a module that can monitor CAN
bus signals.
Syntax
:CHANnel<x1>:CAN:SCHannel<x2>:
ZOOM {<NRf>}
:CHANnel<x1>:CAN:SCHannel<x2>:ZOOM?
CAN Bus Monitor Module (720240) or
the CAN/CAN FD monitor module (720242)
<x1> = 1 to 4
CAN & LIN Bus Monitor Module (720241)
<x1> = 1, 3
<x2> = 1 to 60
<NRf> = 0.1, 0.111, 0.125, 0.143, 0.167, 0.2, 0.25,
0.33, 0.4, 0.5, 0.556, 0.625, 0.667, 0.714,
0.8, 0.833, 1, 1.11, 1.25, 1.33, 1.43, 1.67,
2, 2.22, 2.5, 3.33
Example
:CHANNEL3:CAN:SCHANNEL1:ZOOM 1
:CHANNEL3:CAN:SCHANNEL1:ZOOM?
-> :CHANNEL3:CAN:SCHANNEL1:ZOOM 1
Description This command is valid when the data type is
logic.
:CHANnel<x>:DISPlay
Function Sets or queries whether the channel is displayed.
Syntax
:CHANnel<x>:DISPlay {<Boolean>}
:CHANnel<x>:DISPlay?
<x> = 1 to 4
Example
:CHANNEL1:DISPLAY 1
:CHANNEL1:DISPLAY?
-> :CHANNEL1:DISPLAY 1
Description An error will occur if there is no module installed
in the channel (slot).
When setting,
error 113: Undefined header
When querying,
error 420: Query UNTERMINATED
4.6 CHANnel Group