YOKOGAWA DL350 User Manual

4-64
IM DL350-17EN
:CHANnel<x1>:SENT:SCHAnnel<x2>:BIT<x
3>:DISPlay
Function Sets or queries whether each bit of SENT data is
to be displayed.
Syntax
:CHANnel<x1>:SENT:SCHannel<x2>:
BIT<x3>:DISPlay {<Boolean>}
:CHANnel<x1>:SENT:SCHannel<x2>:
BIT<x3>:DISPlay?
<x1> = 1 to 4
<x2> = 4, 10
<x3> S&C Channel: 1 to 4
Error Trigger: 1 to 5
Example
:CHANNEL1:SENT:SCHANNEL1:BIT1:
DISPLAY ON
:CHANNEL1:SENT:SCHANNEL1:BIT1:
DISPLAY?
-> :CHANNEL1:SENT:SCHANNEL1:BIT1:
DISPLAY ON
Description • This command is valid for a sub channel whose
data type is set to S&C or Error Trigger.
• For an error trigger channel, this is equivalent
to a :CHANnel<x>:SENT:ERRor:TRIGger:*****
command.
:CHANnel<x1>:SENT:SCHAnnel<x2>:BIT<x
3>:LABel
Function Sets or queries the display label of each bit of
SENT data.
Syntax
:CHANnel<x1>:SENT:SCHannel<x2>:
BIT<x3>:LABel {<String>}
:CHANnel<x1>:SENT:SCHannel<x2>:
BIT<x3>:LABel?
<x1> = 1 to 4
<x2> = 4, 10
<x3> S&C Channel: 1 to 4
Error Trigger: 1 to 5
<String> = Up to 16 characters
Example
:CHANNEL1:SENT:SCHANNEL1:BIT1:
LABel “Bit0”
:CHANNEL1:SENT:SCHANNEL1:BIT1:LABel?
-> :CHANNEL1:SENT:SCHANNEL1:BIT1:
LABel “Bit0”
Description • This command is valid for a sub channel whose
data type is set to S&C or Error Trigger.
• For an error trigger sub channel, the setup
menu displayed on the instrument’s panel does
not contain a menu command that corresponds
to this command.
:CHANnel<x1>:SENT:SCHAnnel<x2>:BORD
er (Byte Order)
Function Sets or queries the endian (byte order) of SENT
data.
Syntax
:CHANnel<x1>:SENT:SCHannel<x2>:
BORDer {BIG|LITTle}
:CHANnel<x1>:SENT:SCHannel<x2>:
BORDer?
<x1> = 1 to 4
<x2> = 1 to 3, 5 to 9
Example
:CHANNEL1:SENT:SCHANNEL1:BORDER BIG
:CHANNEL1:SENT:SCHANNEL1:BORDER?
-> :CHANNEL1:SENT:SCHANNEL1:
BORDER BIG
Description This command can be used on a sub channel
whose data type is set to FastCH.
:CHANnel<x1>:SENT:SCHAnnel<x2>:DTYPe
Function Sets or queries the data type of SENT data.
Syntax
:CHANnel<x1>:SENT:SCHannel<x2>:
DTYPe {FACHannel|SLCHannel}
<x1> = 1 to 4
<x2> = 5 to 9
:CHANnel<x1>:SENT:SCHannel<x2>:
DTYPe?
<x1> = 1 to 4
<x2> = 1 to 11
Response parameter = {FACHannel|
SLCHannel|SCALibration|ERTRigger|
ERCount}
FACHannel: Fast Channel
SLCHannel: Slow Channel
SCALibration: Status and Calibration
ERTRigger: Error Trigger
ERCount: Error Counter
Example
:CHANNEL1:SENT:SCHANNEL5:
DTYPE SLCHANNEL
:CHANNEL1:SENT:SCHANNEL5:DTYPE?
-> :CHANNEL1:SENT:SCHANNEL5:
DTYPE SLCHANNEL
Description For queries, the following values are returned for
each sub channel.
Sub channels 1, 2, 3: FACHannel
Sub channel 4: SCALibration
Sub channels 5, 6, 7, 8, 9:
SLCHannel, FACHannel
Sub channel 10: ERTRigger
Sub channel 11: ERCount
4.6 CHANnel Group

YOKOGAWA DL350 Specifications

General

Brand	YOKOGAWA
Model	DL350
Category	Recording Equipment
Language	English