YOKOGAWA DL350 - Page 98

4-71
IM DL350-17EN
Commands
1
2
3
4
5
App
Index
:CHANnel<x1>:TEMPerature:SCHannel<x2
>:BURNout
Function Sets or queries whether burnout will be detected
when temperature measurements are performed
on a 16-CH temperature/voltage input module.
Syntax
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:BURNout {<Boolean>}
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:BURNout?
<x1> = 1, 3
<x2> = 1 to 16
Example
:CHANNEL1:TEMPERATURE:SCHANNEL1:
BURNOUT ON
:CHANNEL1:TEMPERATURE:SCHANNEL1:
BURNOUT?
-> :CHANNEL1:TEMPERATURE:SCHANNEL1:
BURNOUT 1
Description This command is valid when the input coupling
is set to TC. If the input coupling is not set to TC,
Error 113, “Undefined header,” will occur.
:CHANnel<x1>:TEMPerature:SCHannel<x2
>:COUPling
Function Sets or queries the input coupling setting of a 16-
CH temperature/voltage input module.
Syntax
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:COUPling {DC|TC|GND|
OFF}
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:COUPling?
<x1> = 1, 3
<x2> = 1 to 16
Example
:CHANNEL1:TEMPERATURE:SCHANNEL1:
COUPLING TC
:CHANNEL1:TEMPERATURE:SCHANNEL1:
COUPLING?
-> :CHANNEL1:TEMPERATURE:SCHANNEL1:
COUPLING TC
:CHANnel<x1>:TEMPerature:SCHannel<x2
>:LABel
Function Sets or queries the channel label when
temperature measurements are performed on a
16-CH temperature/voltage input module.
Syntax
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:LABel {<String>}
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:LABel?
<x1> = 1, 3
<x2> = 1 to 16
Example
:CHANNEL1:TEMPERATURE:SCHANNEL1:
LABEL “CH1_1”
:CHANNEL1:TEMPERATURE:
SCHANNEL1:LABEL?
-> :CHANNEL1:TEMPERATURE:
SCHANNEL1:LABEL “CH1_1”
Description This command is valid when the input coupling
is set to TC. If the input coupling is not set to TC,
Error 113, “Undefined header,” will occur.
:CHANnel<x1>:TEMPerature:SCHannel<x2
>:RJC
Function Sets or queries the RJC when temperature
measurements are performed on a 16-CH
temperature/voltage input module.
Syntax
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:RJC {<Boolean>}
:CHANnel<x1>:TEMPerature:
SCHannel<x2>:RJC?
<x1> = 1, 3
<x2> = 1 to 16
Example
:CHANNEL1:TEMPERATURE:SCHANNEL1:
RJC 1
:CHANNEL1:TEMPERATURE:SCHANNEL1:RJC?
-> :CHANNEL1:TEMPERATURE:SCHANNEL1:
RJC 1
Description This command is valid when the input coupling
is set to TC. If the input coupling is not set to TC,
Error 113, “Undefined header,” will occur.
4.6 CHANnel Group