YOKOGAWA DpharpEJX vigilantplant EJX Series - Integration of DD

IM 01C25T01-01E
3-13
3. OPERATION
d. User Setting of Engineering Unit and Scale
Enter disp range parameters allow the engineering
unit and scale to be displayed. At Set Engr Unit, the
following engineering units can be selected from a list.
Alternately, up to eight alphanumeric characters,
spaces or slashes (/) can be input on the keypad at
Modify Engr Unit; only the first six are displayed on
the integral indicator.
Select the unit from the Set Engr Unit list.
FX0302.EPS
kPa
MPa
mbar
bar
psi
psia
mmH2O
mmHg
mmHgA
mmAq
mmWG
Torr
inH2O
inHg
inHgA
ftH2O
gf/cm2
kgf/cm2
kg/cm2G
kg/cm2A
atm
kg/h
t/h
m3/h
m3/min
l/h
l/min
kl/h
kl/min
Nl/h
Nl/min
Nm3/h
Nm3/min
ACFH
ACFM
SCFH
SCFM
GPH
GPM
m
mm
in
ft
kg/m3
g/cm3
Follow the procedure below to set your own unit.
Example: Set the engineering unit as M/h.
F0321.EPS
EJX:YOKOGAWA
Enter Engr Unit:
M/H
HELP DEL ABORT ENTER
1. Device setup
4. Detailed setup
4. Display condition
4. Engr disp range
7. Modify Engr Unit
Call up the Modify Engr Unit.
Set M/H, and press ENTER (F4).
1
(ENTER)
EJX:YOKOGAWA
Enter space on the
characters to be
lowercase:
M/H
M/
HELP DEL ABORT ENTER
Enter a space instead of a character
to display the character in
lowercase, and press ENTER (F4).
2
(ENTER)
×2
Note that following symbols are not available:
# % & < > . * : + -
The integral indicator shows “-- -- -- -- -- --” when
these are entered.
Engr LRV and Engr URV are used to set the lower
and upper range values for the engineering unit
display. When the insrument is shipped, these are set
as specified in the order.
F0322.EPS
Call up the Engr LRV Display.Set
–50, and press ENTER (F4).
EJX:YOKOGAWA
Engr LRV
0.0
-50
DEL DEL ESC ENTER
EJX:YOKOGAWA
Engr disp range
1 Engr LRV -50
2 Engr URV 100
3 Engr exp !1
4 Engr Unit M
5 Engr point 1
HELP SEND HOME ENTER
Press to select engr disp URV.
EJX:YOKOGAWA
Engr URV
100.0
50
DEL DEL ESC ENTER
Set 50, and press ENTER (F4).
HELP
(ENTER)
‘– 5 0’
(ENTER)
‘5 0’
(SEND)
1. Device setup
4. Detailed setup
4. Display condition
4. Engr disp range
1. Engr LRV and 2. Engr URV
Example: Set lower range value (LRV) to –50 and upper
range value (URV) to 50.
1
2
EJX:YOKOGAWA
Engr disp range
1 Engr LRV -50
2 Engr URV 50
3 Engr exp !1
4 Engr Unit M
5 Engr point 1
HELP SEND HOME ENTER
4
3
Press SEND (F2) to send the data
to the transmitter, then check to
confirm that disappears.
(SEND)
SEND