YOKOGAWA SC41 - Typical Installation SC4 A-*-PR; Dimensions SC4 A Sensors

IM 12D07J01-10E-E
9
2.2.3. Typical installation SC4A-*-PR
The installation of the SC4A-*-PR sensor is done using the Model PR10 retractable fitting.
The mounting procedure of the sensor is explained in the Instruction Manual of this fitting.
2.3. Dimensions SC4A sensors
units in mm (inch)
Ø 19,1
(0.75")
90 (3.55")
Ø 25
(1.00")
Ø 38 x 5
(1.50 x 0.20)
95 (3.74")
25
(1.00”)
Ø50,4
(1.98")
Ø19
(0.75")
1 - 1.5 "
tri-clamp
2 "
tri-clamp
Ø25
(1.00")
80 (3.15")
Ø63,9
(2.52")
M19x1.5
48 (1.89")
19.8
Ø 24.9
Ø 19.1
152 (5.98")
152 (5.98")
95 (3.74")
70 (2.75")
41
52
Ø 27.5
Ø 19.1
Ø 64
Ø 25
Ø 50.5
Ø 19.1
Ø 19.1
2 "
tri-clover
1" - 1
1
/
2
"
tri-clover
70
80
Ø 19,1
(0.75")
90 (3.55")
Ø 25
(1.00")
Ø 38 x 5
(1.50 x 0.20)
95 (3.74")
25
(1.00”)
Ø50,4
(1.98")
Ø19
(0.75")
1 - 1.5 "
tri-clamp
2 "
tri-clamp
Ø25
(1.00")
80 (3.15")
Ø63,9
(2.52")
M19x1.5
48 (1.89")
19.8
Ø 24.9
Ø 19.1
152 (5.98")
152 (5.98")
95 (3.74")
70 (2.75")
41
52
Ø 27.5
Ø 19.1
Ø 64
Ø 25
Ø 50.5
Ø 19.1
Ø 19.1
2 "
tri-clover
1" - 1
1
/
2
"
tri-clover
70
80
Fig 7. SC4A-AD Fig. 8. SC4A-SA Fig. 9. SC4A-PR
Ø 19,1
(0.75")
90 (3.55")
Ø 25
(1.00")
Ø 38 x 5
(1.50 x 0.20)
95 (3.74")
25
(1.00”)
Ø50,4
(1.98")
Ø19
(0.75")
1 - 1.5 "
tri-clamp
2 "
tri-clamp
Ø25
(1.00")
80 (3.15")
Ø63,9
(2.52")
M19x1.5
48 (1.89")
19.8
Ø 24.9
Ø 19.1
152 (5.98")
152 (5.98")
95 (3.74")
70 (2.75")
41
52
Ø 27.5
Ø 19.1
Ø 64
Ø 25
Ø 50.5
Ø 19.1
Ø 19.1
2 "
tri-clover
1" - 1
1
/
2
"
tri-clover
70
80
Fig. 10 : Dimensions of SC4A-SB/SC sensor
Ø 19,1
(0.75")
90 (3.55")
Ø 25
(1.00")
Ø 38 x 5
(1.50 x 0.20)
95 (3.74")
25
(1.00”)
Ø50,4
(1.98")
Ø19
(0.75")
1 - 1.5 "
tri-clamp
2 "
tri-clamp
Ø25
(1.00")
80 (3.15")
Ø63,9
(2.52")
M19x1.5
48 (1.89")
19.8
Ø 24.9
Ø 19.1
152 (5.98")
152 (5.98")
95 (3.74")
70 (2.75")
41
52
Ø 27.5
Ø 19.1
Ø 64
Ø 25
Ø 50.5
Ø 19.1
Ø 19.1
2 "
tri-clover
1" - 1
1
/
2
"
tri-clover
70
80