YOKOGAWA UP35A Operation Guide

IM 05P02D41-11EN page 1/14
Contents
1. Safety Precautions
2. ModelandSufxCodes
3. How to Install
4. HardwareSpecications
5. HowtoConnectWires
6. TerminalWiringDiagrams
Introduction
ThankyouforpurchasingtheUP35A/UP32AProgramController.
Thisoperationguidedescribesthebasicoperationsrelatedtothesingle-loopcontrol
functionoftheUP35A/UP32A.Theguideshouldbeprovidedtotheenduserofthis
product.
Besuretoread thisoperationguidebefore usingtheproductin ordertoensure
correct operation.
Fordetailsofeachfunction,refertotheelectronicmanual.Beforeusingtheproduct,
refertothetableofModelandSufxCodestomakesurethatthedeliveredproduct
isconsistentwiththemodelandsufxcodesyouordered.Alsomakesurethatthe
followingitemsareincludedinthepackage.
•ProgramController(themodelyouordered) ..........................................x1
• Set of Brackets ........................................................................................x1
•UnitLabel(L4502VZ) ..............................................................................x1
•TagLabel(L4502VE) ..............................................................................x1
(Onlywhenordered.)
•TerminalCover(L4502XP) .....................................................................x1
•OperationGuide(thisdocument) ............................................................x7(A3size)
(InstallationandWiring,InitialSettings,Programming,Operations,andParameters)
l
TargetReaders
Thisguideisintendedforthefollowingpersonnel;
• Engineersresponsibleforinstallation,wiring,andmaintenanceoftheequipment.
• Personnelresponsiblefornormaldailyoperationoftheequipment.
1. Safety Precautions
Thefollowingsymbolisusedonthe instrument.Itindicates thepossibilityofinjury
totheuserordamagetotheinstrument,andsigniesthattheusermustrefertothe
operationguideoruser’smanualforspecialinstructions.Thesamesymbolisused
intheoperationguideanduser’smanualonpages thattheuserneedsto referto,
togetherwiththeterm“WARNING”or“CAUTION.”
WARNING
Calls attention to actions or conditions that could cause serious
or fatal injury to the user, and indicates precautions that should be
taken to prevent such occurrences.
CAUTION
Calls attention to actions or conditions that could cause injury to
the user or damage to the instrument or property and indicates pre-
cautions that should be taken to prevent such occurrences.
AC
AC/DC
Theequipmentwhollyprotectedbydoubleinsulationorreinforcedinsulation.
Functionalgroundingterminals
  (Donotusethisterminalasaprotectivegroundingterminal).
Note
Identiesimportantinformationrequiredtooperatetheinstrument.
■ Warning and Disclaimer
(1) YOKOGAWAmakesnowarrantiesregardingtheproductexceptthosestatedin
theWARRANTYthatisprovidedseparately.
(2) Theproductisprovidedonan"asis"basis.YOKOGAWAassumesnoliabilityto
anypersonorentity foranylossor damage,directorindirect,arisingfromthe
useoftheproductorfromanyunpredictabledefectoftheproduct.
■ Safety,Protection,andModicationoftheProduct
(1)Inorder toprotectthe systemcontrolledbythisproductandthe productitself,
andtoensuresafe operation,observethesafety precautionsdescribedinthe
operationguide.Use oftheinstrumentinamannernot prescribedhereinmay
compromise the product's functions and the protection features inherent in the
device.Weassumenoliabilityforsafety,orresponsibilityfortheproduct'squality,
performanceorfunctionalityshouldusersfailtoobservetheseinstructionswhen
operatingtheproduct.
(2)Installation ofprotectionand/or safetycircuitswithrespect toalightning
protector;protectiveequipmentforthesystemcontrolledbytheproductandthe
productitself;foolproof orfailsafedesign ofaprocess orlineusing thesystem
controlledbytheproductortheproductitself;and/orthedesignandinstallation
ofotherprotectiveandsafetycircuitsaretobeappropriatelyimplementedasthe
customer deems necessary.
(3) Besuretouse thesparepartsapproved byYOKOGAWAwhenreplacing parts
orconsumables.
(4) Thisproductisnot designedormanufactured tobeusedin criticalapplications
thatdirectlyaffectorthreatenhuman lives.Suchapplicationsincludenuclear
powerequipment,devicesusing radioactivity,railway facilities,aviation
equipment,airnavigationfacilities,aviationfacilities,andmedicalequipment.
Ifsoused, itistheuser’sresponsibility toincludein thesystemadditional
equipmentanddevicesthatensurepersonnelsafety.
(5) Modicationoftheproductisstrictlyprohibited.
(6)
Thisproductisintendedtobehandledbyskilled/trainedpersonnelforelectricdevices.
(7)ThisproductisULRecognizedComponent.Inordertocomplywith UL
standards,end-productsarenecessary tobedesignedby thosewhohave
knowledgeoftherequirements.
WARNING
l
Power Supply
Ensure that the instrument’s supply voltage matches the voltage
of the power supply before turning ON the power.
l
Do Not Use in an Explosive Atmosphere
Do not operate the instrument in locations with combustible
or explosive gases or steam. Operation in such environments
constitutes an extreme safety hazard. Use of the instrument in
environments with high concentrations of corrosive gas (H
2
S,
SO
X
, etc.) for extended periods of time may cause a failure.
l
Do Not Remove Internal Unit
The internal unit should not be removed by anyone other than
YOKOGAWA's service personnel. There are dangerous high voltage
parts inside. Additionally, do not replace the fuse by yourself.
l
Damage to the Protective Construction
Operation of the instrument in a manner not specified in the
operation guide may damage its protective construction.
CAUTION
This instrument is an EMC class A product. In a domestic environ-
ment this product may cause radio interference in which case the
user needs to take adequate measures.
2. ModelandSufxCodes
■ UP35A «for Standard Code Model»
Model Sufxcode
Option
code
Description
UP35A
ProgramController(Powersupply:100-240VAC)
2programpatterns/20programsegments(When
the/APoptionisspecied,4programpatterns/40
programsegments,max.20segmentsperpattern.)
(providedwithretransmissionoutputor15VDC
looppowersupply,3DIs,and3DOs)
Type1:
Basic
control
-0 Standard type
-1 Position proportional type
-2 Heating/coolingtype
Type2:
Functions
0 None
1 5additionalDOs,5additionalDIs
Type3:Open
networks
0 None
1
RS-485communication(Max.38.4kbps,2-wire/4-wire)
2
Ethernetcommunication(withserialgatewayfunction)
3
CC-Linkcommunication(withModbusmasterfunction)
4
PROFIBUS-DPcommunication(withModbusmasterfunction)
5
DeviceNetcommunication(withModbusmasterfunction)
Displaylanguage(*1)
-1
English(Default.Canbeswitchedtootherlanguagebythesetting.)
-2
German(Default.Canbeswitchedtootherlanguagebythesetting.)
-3
French(Default.Canbeswitchedtootherlanguagebythesetting.)
-4
Spanish(Default.Canbeswitchedtootherlanguagebythesetting.)
Casecolor
0 White(Lightgray)
1 Black(Lightcharcoalgray)
Fixedcode -00 Always"-00"(forStandardCodeModel)
Optioncodes
/AP
Additional 2programpatterns/20programsegments
/HA Heaterbreakalarm(*2)
/DC Powersupply24VAC/DC
/CT Coating(*3)
/CV TerminalCover
*1: English,German,French,andSpanishareavailablefortheguidedisplay.
*2: The/HAoptioncanbespecifiedonlywhentheType1codeis“-0”or“-2.”
*3: Whenthe/CToptionisspecified,theUP35Adoesnotconformtothesafetystandards(UL
andCSA)andCEmarking(Productswith/CToptionarenotintendedforEEA-market).
■ UP32A «for Standard Code Model»
Model Sufxcode
Option
code
Description
UP32A
ProgramController(Powersupply:100-240VAC)
2programpatterns/20programsegments(When
the/APoptionisspecied,4programpatterns/40
programsegments,max.20segmentsperpattern.)
(providedwithretransmissionoutputor15VDC
looppowersupply,3DIs,and3DOs)
Type1:
Basic
control
-0 Standard type
-1 Position proportional type
-2 Heating/coolingtype
Type2:
Functions
0 None
1
RS-485communication(Max.38.4kbps,2-wire/4-wire)
2 2additionalDIs,2additionalDOs
Type3:Open
networks
0 None
3
CC-Linkcommunication(withModbusmasterfunction)(*1)
Displaylanguage(*2)
-1
English(Default.Canbeswitchedtootherlanguagebythesetting.)
-2
German(Default.Canbeswitchedtootherlanguagebythesetting.)
-3
French(Default.Canbeswitchedtootherlanguagebythesetting.)
-4
Spanish(Default.Canbeswitchedtootherlanguagebythesetting.)
Casecolor
0 White(Lightgray)
1 Black(Lightcharcoalgray)
Fixedcode -00 Always"-00"(forStandardCodeModel)
Optioncodes
/AP
Additional 2programpatterns/20programsegments
/HA Heaterbreakalarm(*3)
/DC Powersupply24VAC/DC
/CT Coating(*4)
/CV TerminalCover
*1: Type3code“3”canbespecifiedonlywhenbothType1andType2codeare“0”.
*2: English,German,French,andSpanishareavailablefortheguidedisplay.
*3:
The/HAoptioncanbespecifiedonlywhentheType1codeis“-0”or“-2”andType3codeis“0”.
*4: Whenthe/CToptionisspecified,theUP32Adoesnotconformtothesafetystandards(UL
andCSA)andCEmarking(Productswith/CToptionarenotintendedforEEA-market).
■ Accessories (sold separately)
Thefollowingisanaccessorysoldseparately.
• LL50AParameterSettingSoftware
Model Sufxcode Description
LL50A -00 ParameterSettingSoftware
• ExternalPrecisionResistor
Model Sufxcode Description
X010 SeetheGeneralSpecications(*) ResistanceModule
 *:Necessarytoinputthecurrentsignaltothevoltageinputterminal.
• TerminalCover:ModelUTAP001
• TerminalCover
 ModelUTAP001forUP35A,ModelUTAP002forUP32A
• Manuals
 Note:Manualscanbedownloadedfromawebsite.
 URL:http://www.yokogawa.com/ns/ut/im/
• Brackets
 Partnumber:L4502TP(2pcsforupperandlowersides)
3. How to Install
■ Installation Location
Theinstrumentshouldbeinstalledinindoor locationsmeetingthe following
conditions:
• Instrumented panel
 Thisinstrumentisdesignedto bemountedinan instrumentedpanel.Mountthe
instrumentinalocationwhereitsterminalswillnotinadvertentlybetouched.
• Well ventilated locations
 Mounttheinstrumentinwellventilatedlocationstopreventtheinstrument’sinter-
naltemperaturefromrising.
 However,makesurethattheterminalportionsarenotexposedtowind.Exposure
to wind may cause the temperature sensor accuracy to deteriorate. To mount mul-
tipleindicatingcontrollers, seetheexternal dimensions/panelcutoutdimensions
whichfollow.Ifmountingotherinstrumentsadjacenttotheinstrument,complywith
thesepanelcutoutdimensionstoprovidesufcientclearancebetweentheinstru-
ments.
• Locations with little mechanical vibration
 Installtheinstrumentinalocationsubjecttolittlemechanicalvibration.
• Horizontal location
 Mounttheinstrumenthorizontallyandensurethatitislevel,withnoinclinationto
therightorleft.
Front panel
of controller
Keep this angle
within 30°
Rear of
controller
30°
Note
Iftheinstrument ismovedfrom alocationwith lowtemperatureand lowhumidity
toaplacewith hightemperatureandhighhumidity,orifthetemperaturechanges
rapidly,condensationwill result.Moreover,in thecaseof thermocoupleinputs,
measurementerrorswillresult.Toavoidsuchasituation,leavetheinstrumentinthe
newenvironmentunderambientconditionsformorethan1hourpriortousingit.
Donotmounttheinstrumentinthefollowinglocations:
• Outdoors
• Locations subject to direct sunlight or close to a heater
 Installtheinstrumentinalocationwithstabletemperaturesthatremainclosetoan
averagetemperatureof23°C.Donotmountitinlocationssubjecttodirectsunlight
orclosetoaheater.Doingsoadverselyaffectstheinstrument.
• Locations with substantial amounts of oily fumes, steam, moisture, dust, or
corrosive gases
 Thepresenceofoilyfumes,steam,moisture,dust,or corrosivegasesadversely
affectstheinstrument.Donotmounttheinstrumentinlocationssubjecttoanyof
thesesubstances.
• Areasnearelectromagneticeldgeneratingsources
 Donotplacemagnetsortoolsthatgeneratemagnetismneartheinstrument.Ifthe
instrumentisusedin locationsclosetoa strongelectromagneticeldgenerating
source,themagneticeldmaycausemeasurementerrors.
• Locationswherethedisplayisdifculttosee
 TheinstrumentusesanLCD forthedisplayunit,andthiscanbedifculttosee
fromextremelyobliqueangles.Mounttheinstrumentinalocationwhereitcanbe
seenasmuchaspossiblefromthefront.
• Areasclosetoammablearticles
 Absolutelydonotplace theinstrumentdirectlyonam-
mablesurfaces.Ifsuchacircumstanceis unavoidable
andtheinstrumentmustbeplacedclosetoaammable
item,provideashieldforitmadeof1.43mmthickplated
steel or 1.6 mm thick unplated steel with a space of at
least150mmbetweenitandtheinstrumentonthetop,
bottom,andsides.
• Areas subject to being splashed with water
WARNING
Be sure to turn OFF the power supply to the controller before in-
stalling it on the panel to avoid an electric shock.
www.yokogawa.com/ns
YOKOGAWA ELECTRIC CORPORATION
Network Solutions Business Division
2-9-32, Naka-cho Musashino-shi, Tokyo 180-8750 JAPAN
YOKOGAWA CORPORATION OF AMERICA
Head office and for product sales
2 Dart Road, Newnan, Georgia 30265, USA
YOKOGAWA EUROPE B.V.
Headquarters
Euroweg 2, 3825 HD Amersfoort, THE NETHERLANDS
All Rights Reserved, Copyright © 2010 Yokogawa Electric Corporation
150 mm150 mm
150 mm
150 mm
Operation
Guide
IM 05P02D41-11EN
UP35A/UP32A
Program Controller
Operation Guide
This operation guide describes installation, wiring, and other tasks required to make the
controller ready for operation.
4th Edition : Mar. 2016
Installation and Wiring
For details of the each function, refer to the electronic manual. M
anuals can be
downloaded or viewed at the following URL.
Functional
Enhancement
http://www.yokogawa.com/ns/ut/im/
«Standard Code Model»
• AuthorisedRepresentativeintheEEA
 Yokogawa EuropeBV. (Address:Euroweg2,3825HDAmersfoort,The
Netherlands)istheAuthorisedRepresentativeofYokogawaElectric Corporation
forthisProductintheEEA.
• Printed Manuals
Model Description
UP35A/UP32AProgramControllerOperationGuide«StandardCodeModel» IM05P02D41-11EN
UP35AProgramControllerOperationGuide«DetailedCodeModel» IM05P02D41-15EN
PrecautionsontheUseoftheUTAdvancedSeries IM05P01A01-11EN
• ElectronicManuals
 Youcandownloadthelatestmanualsfromthefollowingwebsite:
 URL:http://www.yokogawa.com/ns/ut/im/
Model Description
UP35A/UP32AProgramControllerOperationGuide«StandardCodeModel» IM05P02D41-11EN
UP35AProgramControllerOperationGuide«DetailedCodeModel» IM05P02D41-15EN
UP35A/UP32AProgramControllerUser’sManual IM05P02D41-01EN
UTAdvancedSeriesCommunicationInterface(RS-485,Ethernet)User’sManual IM05P07A01-01EN
UTAdvancedSeriesCommunicationInterface(OpenNetwork)User’sManual IM05P07A01-02EN
LL50AParameterSettingSoftwareInstallationManual IM05P05A01-01EN
LL50AParameterSettingSoftwareUser’sManual IM05P05A01-02EN
PrecautionsontheUseoftheUTAdvancedSeries IM05P01A01-11EN
• GeneralSpecication
Model Description
UP35A/UP32AProgramController GS05P02D41-01EN
LL50AParameterSettingSoftware GS05P05A01-01EN
* Thelasttwocharactersofthemanualnumberandgeneralspecificationnumberindicatethe
languageinwhichthemanualiswritten.

YOKOGAWA UP35A Specifications

General

Brand	YOKOGAWA
Model	UP35A
Category	Controller
Language	English