Name: 3D Systems DMP Flex 350
Brand: 3D Systems
Rating: 4 (1 reviews)

To Next Page

DMP Flex 350

Production printer

User guide

Original instructions

Table of Contents2
Limitations of Warranty and Liability6
Intended Use6
Inert Gas Requirement6
Introduction6
Oxygen Limits7
Copyright7
Related Documentation7
Safety Precautions7
Definitions and Names8
Safety Guidelines9
Safety Labels9
Foreseeable Misuse17
Mechanical Hazards18
Contact Hazards18
Personal Protective Equipment (PPE)18
Electrical Hazards18
Fumes18
Residual Risks18
Radiation Hazards19
Thermal Hazards19
Material Substance Hazards19
Sharp Edges on the Printed Part19
Weak Mechanical Integrity on the Printed Parts19
Special Considerations - Reactive Metals20
Electrical Equipment20
Fire Suppression20
Good Housekeeping20
Electrical Lockout-Tagout Procedure21
Rules21
Principles, Beliefs and Philosophy21
Policy21
Lock-Out/Tag-Out21
Remove Energy Stored in Argon and Compressed Air Lines22
Restore Equipment to Service22
Procedure Involving more than One Person22
Safety Interlocks23
Stack Light23
Shut-Off Matrix25
Dmp Flex 350 at a Glance26
DMP Flex 350 Hardware Configurations26
DMP Flex 350 Start-Up Set27
Dmp Flex28
Software Overview35
3Dxpert35
DMP Main Toolbar36
How to Begin37
DMP Control - Operator38
Menu Bar38
Preview Screen39
Positioning & Tools Panel40
Layers Slider Bar40
Properties41
Update Scanner Calibration File42
Checking Slicing/Hatching Parameters43
Building Close to the Platform Borders44
Configure Automatic Job File Backup45
Options for the Materialbatchnumberformatmask Setting46
E-Mail Notifications48
DMP Deposition - Operator49
Oxygen/Pressure Status49
Machine Status49
Menu Bar50
Tabs54
DMP Monitoring (Optional)62
DMP Server62
Backup DMP Server62
Bringing DMP Server to a Domain62
System Use63
Start Up Dmp Flex63
Prepare System65
Add Powder65
Install Build Plate65
Install New Coater Strip66
Prepare Build Plate68
Clean Laser Window69
Inert System70
Close Printer Door70
Run Inertion Cycle71
Start Job73
Remove Printed Parts74
Remove Used Material78
Change Material79
Swap Printer Modules79
Change Powder in a Single Printer Module81
Emergency off84
Location84
What Happens84
Restart after Emergency off85
Shut Down Dmp Flex85
User Maintenance86
Preventive Maintenance86
Overview Table86
Clean Machine Interior and Printer Module87
Before Every Print Job87
Clean Laser Window90
Monthly91
Check Pressure Levels91
Check Emergency off Buttons91
Check Chiller Temperature and Water Level92
Clean Vent Opening92
Check Printer Gloves92
Automatic Laser Power Calibration93
Every 3 Months98
Replace Chiller Fluid98
Clean Machine Exterior98
Check Oil Level Blower99
Check Oil Level Vacuum Pump99
Replace Process Filter100
After 1600 Job Hours100
Every 6 Months / 2000 Hours112
Clean Overpressure Valve112
Clean Vacuum Pump Ventilator112
Troubleshooting113
Client Software (DMP Control, DMP Explorer113
Change, Repair or Uninstall DMP Software113
Re-Install Scanner Driver Files113
Symptoms113
Prerequisites113
Solution113
Reinstall or Restore a Broken DMP Server Computer114
DMP Explorer115
Solid Supports Are Failing to Process115
Processing Fails with "Errors During Hatching115
- Slicing and Hatching a Large, Complex Part Takes Longer than 2 Days and Crashes116
- Processing of Block Supports Fails117
- Speed up the Slicing, Hatching and Processing of Multiple Parts117
- My Computer Is Slow When DMP Worker Is Enabled117
- Dmp Deposition118
- Fix 'Unsafe Filter Pressure' Message118
- Detecting of Job Processing Capability Failed after Restarting DMP Deposition118
- Basic Regulations119
EC Declaration of Conformity (Doc)119

Brand	3D Systems
Model	DMP Flex 350
Category	3D Printers
Language	English

3D Systems DMP Flex 350 User Manual

Table of Contents

Other manuals for 3D Systems DMP Flex 350

Questions and Answers:

3D Systems DMP Flex 350 Specifications

Related product manuals