ABB CM30 - Page 2

Refer to Section 7.1, page 24 Refer to Section 7.2, page 26 Refer to Section 7.3, page 32
Refer to Section 7.5, page 47
Refer to Section 7.4, page 36
Refer to Section 7.6, page 49 Refer to Section 7.7, page 53 Refer to Section 7.8, page 58 Refer to Section 7.10, page 63Refer to Section 7.9, page 59
Refer to Section 6, page 18
Basic Level *Advanced Level…
Loop 1 (2) Setpoints
Local Setpoint 1 (4)
RSP Ratio
RSP Bias
Ramp Mode
Ramp Rate

Loop 1 (2) Control
On/Off
Mode
Autotune
PID
FeedForward

Loop 1 (2) Mot Valve
Ratio
Bias
Deadband
Travel Time
Loop 1 (2) Time Prop 
Cycle Time 1 (2)

Alarm 1 (8)
Trip
Initial Setup
App. Template
Loop 1 (2) Output Type
Loop 1 (2) Split O/P
Instrument Tag
Loop 1 (2) Tag
Mains Freq.
Config Action
Custom Template
Reset to Defaults
Security Setup
Basic Password
Advanced Password
Reset Passwords
Custom Config
Off 
Loop 1 (2) PV
Loop 1 (2) Split O/P
Loop 1 (2) Valve O/P
Loop 1 (2) Valve FB
Loop 1 (2) TP OP1 (2)
Loop 1 (2) RSP
Language

Operator Templates
Page 1 Template

Operator Functions
Autoscroll
Soft Key Function
Auto Manual Enable
Local Remote Enable
Alarm Ack. Enable
Totalizer Stop/Go
Totalizer Reset
SP Adjust Enable

Chart View
Channel 1
Sample Rate

Settings
Brightness
Contrast**
Date & Time
Date Format
Time & Date
Daylight Saving
DS Start Time
DS Start Occur
DS End Occur
DS Start Day
DS End Day
DS Start Month
DS End Month

Customise Pages
Page Number
Template Type
Titlebar Tag
Parameters
Bargraphs
Icons
Page Colors
Analog Inputs
Anlg Input 1 (4)
Analog Outputs
Analog Output 1 (2)
Digital I/O 
Digital IO 1 (6)
Relays
Relay 1 (4)
Loop 1 (2) Setpoints
Low Limit
High Limit
No. of Local SP’s
Local Setpoint 1 (4)
Track Mode
RSP Ratio
RSP Bias
RSP Fault Action
Default Setpoint
Ramp Mode
Ramp Rate
Select Sources
Loop 1 (2) Control
Control Type
Control Action
On/Off Hysteresis
Autotune
PID
Gain Scheduling
FeedForward
Adaptive Control
Misc.
Loop 1 (2) Output
Limits
Failure Actions
A/M Select Sources
Slew Rate
Tracking
Loop 1 (2) Split O/P
Min Input 1 (2)
Min OP 1 (2)
Max Input 1 (2)
Max OP 1 (2)
Loop 1 (2) Valve
Ratio
Bias
Deadband
Travel time
Loop 1 (2) Time Prop
Cycle Time 1 (2)
Alarm 1 (8)
Type
Tag
Source
Trip
Hysteresis
Time Hysteresis
Display Enable
Acknowledge Source
Enable Source
Totalizer 1 (2)
Mode
Source
Count Direction
Units
Count Rate
Cutoff
Stop Go Source
Total DPs
Preset Count
Predet Count
Intermed’te Count
Wrap Enable
Reset Source
Reset Days
Reset Hour
Logic Equations
Equation Number
Operand 1
Invert 1
Operator 1
Math Blocks
Math Block Number
Block Type
Eng. DPs
Eng. Low
Eng. High
Eng. Units
Fault Action

Linearizer 1 (2)
Delay Timer 1 (2)
Source
Delay Time
On Time
Real Time Alarms
Real Time Alarm 1 (2)
Monday (to Sunday)
Refer to IM/CM/C-EN for
parameter details.
Diagnostic History
Source Analysis
Analog Source
Digital Source
Invalid Sources
Instrument Type
I/O Build
No. Analog Inputs
No. Analog Outputs
No. Relays
No. Digital I/O
Functionality
Serial No.
Hardware Revision
Software Revision
Basic Device Setup Display Input/Output Control
Process Alarm Totalizer Functions Communication Diagnostics Device Info
Menu Menu Menu Menu Menu
Menu Menu Menu Menu Menu Menu
Exit Select Exit Select Exit Select Exit Select Exit Select
Exit Select Exit Select Exit Select Exit Select Exit Select Exit Select
*When in Advanced Level (configuration mode), press and hold the key to return to the standard Operator page – see Fig. 3.1, page 5.
**Enabled for CM30 and CM50 only