ABB FSM4000 - Inlet and Outlet Sections

FSM4000 ELECTROMAGNETIC FLOWMETER | DS/FSM4000-EN REV. L
17
Dimensions – flange device, aluminum sensor housing (shell housing)
Nominal
diameter
Process connection
D
B
L
2 3
C
F
4
F1
4
F2
4
Weight
DN 250 (10")
EN 1092-1, PN 10
1
395 (15.55)
30 (1.18)
450 (17.72)
198 (7.80)
413 (16.26)
427 (16.81)
349 (13.74)
59.5 (131)
EN 1092-1, PN 16
1
405 (15.94)
30 (1.18)
63.5 (140)
EN 1092-1, PN 25
1
425 (16.73)
36 (1.42)
82.5 (182)
EN 1092-1, PN 40
1
450 (17.72)
42 (1.65)
93.5 (206)
ASME B16.5, CL 150
405 (15.94)
35.2 (1.39)
68.5 (151)
ASME B16.5, CL 300
445 (17.52)
52.8 (2.08)
103.5 (228)
JIS 10K
400 (15.75)
37 (1.46)
63.5 (140)
AS2129 table D, E
405 (15.94)
—
68.5 (151)
DN 300 (12")
EN 1092-1, PN 10
1
445 (17.52)
31 (1.22)
500 (19.68)
228 (8.98)
436 (17.17)
450 (17.72)
372 (14.62)
72.5 (160)
EN 1092-1, PN 16
1
460 (18.11)
33 (1.30)
78.5 (173)
EN 1092-1, PN 25
1
485 (19.09)
39 (1.54)
98.5 (217)
EN 1092-1, PN 40
1
515 (20.28)
47 (1.85)
600 (23.62)
138.5 (305)
ASME B16.5, CL
150 485
(19.09)
36.8 (1.45)
500 (19.68)
103.5 (228)
ASME B16.5, CL 300
520 (20.47)
55.8 (2.20)
148.5 (327)
JIS 10K
450 (17.72)
40 (1.57)
78.5 (173)
AS2129 table D, E
455 (17.19)
—
103.5 (228)
DN 350 (14")
EN 1092-1, PN 10
1
505 (19.88)
31 (1.22)
550 (21.65)
267 (10.51)
451 (17.76)
465 (18.31)
416 (16.38)
93.5 (206)
EN 1092
-1, PN 16
1
520 (20.47)
35 (1.38)
108.5 (239)
EN 1092-1, PN 25
1
555 (21.85)
43 (1.69)
143.5 (316)
ASME B16.5, CL 150
535 (21.06)
40.1 (1.58)
128.5 (283)
ASME B16.5, CL 300
585 (23.03)
58.8 (2.31)
196.5 (433)
JIS 10K
490 (19.29)
—
108.5 (239)
AS2129 table D, E
525 (20.67)
—
103.5 (228)
DN 400 (16")
EN 1092-1 PN 10
1
565 (22.24)
31 (1.22)
600 (23.62)
267 (10.51)
493 (19.41)
507 (19.96)
416 (16.38)
101.5 (224)
EN 1092-1 PN 16
1
580 (22.83)
37 (1.46)
124.5 (274)
EN 1092-1 PN 25
1
620 (24.41)
45 (1.77)
168.5 (371)
ASME B16.5 CL 150
595 (23.43)
41.6 (1.64)
173.5 (382)
ASME B16.5 CL 300
650 (25.59)
62.2 (2.45)
262.5 (579)
JIS 10K
560 (22.05)
—
124.5 (274)
AS2129 table D, E
580 (22.83)
—
173.5 (382)
1 Other pressure ratings on request.
2 If a grounding plate is fitted (fastened to one side of the flange), dimension L increases by 5 mm (0.197 in).
3 If protection plates are fitted (fastened to both sides of the flange), dimension L increases by 10 mm (0.394 in).
4 In devices with high temperature design, the dimensions F, F1 and F2 increase by +127 mm (+5.0 in).
Tolerance L: DN 150 to 200: +0 / -3 mm (+0 / -0.018 in), DN 250 to 400: +0 / -5 mm (+0 / -0.197 in)