How to fix 'Filter' message on Adrona Crystal EX Trace Water Filtration Systems?
The "Filter" message on your Adrona Water Filtration System indicates that the pre-filters need replacement (part no. 10320). After replacing the filters, remember to reset the filter counter.
Why do 'LowPres' and 'Running' messages alternate on Adrona Water Filtration Systems?
If your Adrona Water Filtration System displays "LowPres" and "Running" messages alternately, it could be due to low input water pressure (less than 1 bar). This does not affect system operation. Alternatively, the pre-filter or strainer might be clogged. Replace the pre-filter (part no. 10320) or the strainer (part no. 430034).
What to do if Adrona Water Filtration Systems shows 'LowPres'?
If your Adrona Water Filtration System shows a “LowPres” message, it could be due to several reasons. First, check the input water pressure; if it's less than 1 bar, this message may appear. Also, ensure the pre-filter is installed (part no. 10320). A clogged pre-filter or strainer can also cause this issue; replace the pre-filter (part no. 10320) or the strainer (part no. 430034). Finally, verify the solenoid valve is in order; if not, install the solenoid valve UV (part no. 430020).
What does 'TankS' message mean on Adrona Crystal EX Trace Water Filtration Systems?
If your Adrona Water Filtration System displays “TankS”, this could be due to a damaged level switch. Check its operation and replace if necessary. It could also be caused by low RO module productivity, with the system taking more than 4 hours to fill the 30 l PRO tank. If water quality is satisfactory, you can ignore the message. Restart the purification system and ensure water flows out of the OUT pipe. If the message persists, replace the DI module (part no. 10310).
What to do if Adrona Crystal EX Trace shows 'TnkFull' when the tank is empty?
If your Adrona Water Filtration System shows “TnkFull” while the tank is empty, check the tank connection cable. If no tank is connected, ensure the tank plug is in the tank socket.
How to troubleshoot no display on Adrona Crystal EX Trace Water Filtration Systems?
To address the issue of no display indication when your Adrona Water Filtration System is switched on, check the fuse and supply voltage.
Guidance on how to effectively use the manual for system operation and maintenance.
Crucial safety warnings, hazard symbols, and precautions for operating the water purification system.
Official contact information for Adrona SIA for support and inquiries.
Introduction to the Adrona Crystal EX water purification systems and their applications.
Visual identification of the main components and layout of the Adrona water purification system.
Detailed technical specifications for water purity levels required by the system.
Physical dimensions, weight, noise level, and electrical requirements for the system.
Diagrams illustrating the flow of water and the arrangement of system components.
Explanation of the underlying scientific principles and operational logic of the purification system.
Essential criteria and quality standards for the input water supply to the system.
Instructions and considerations for connecting the system to the water supply and drain.
Guidelines for selecting an appropriate location and ensuring adequate space for the system.
Recommended environmental conditions such as temperature and humidity for optimal operation.
Procedures and checks to ensure water tightness and prevent leaks.
Information regarding optional or necessary external components for system functionality.
Steps to take before physically installing the water purification system.
Explanation of the push-fit connection system for tubing used in the Adrona system.
Identification and description of ports and controls located on the system's rear and side panels.
Details and visual guides for the optional 'Pro' tank for water storage.
Step-by-step instructions for installing the system's pre-filter component.
Guide for correctly installing the deionization and polishing modules.
Instructions on how to correctly attach the dispense filter to the system.
Detailed steps for connecting all necessary tubing for system operation.
Guidance on connecting the tank level sensor and power cables.
Information regarding the system's factory calibration status.
Overview of the system's LCD display, status indicators, and button functions.
Procedures for powering on the system and dispensing purified water.
Explanation of how to navigate the system menu and select different operating modes.
A table outlining the recommended replacement intervals for system components.
Detailed instructions for safely removing and replacing the system's pre-filter.
Step-by-step guide for replacing deionization or polishing modules.
Instructions on how to completely drain the water storage tank.
Procedures for cleaning and sanitizing the water storage tank using hydrogen peroxide.
General| Product Water Resistivity at 25°C | 18.2 MΩ·cm |
|---|---|
| Product Water TOC | < 5 ppb |
| Pyrogens (Endotoxins) | < 0.001 EU/ml |
| RNases | Not detected |
| DNases | Not detected |
| Proteases | Not detected |
To Next Page