To Next PageTo Next Page
Need help?Do you have a question about the AERMEC RV and is the answer not in the manual?
Details on Silenced (L), Extra-Silenced (E), and High Ambient Temperature (A) versions.
Details on heat pump models available in Silenced (HL) and Extra-Silenced (HE) versions.
Describes Total Recovery (T) and Desuperheater (D) options for heat recovery.
Explanation of the microprocessor control system and internal memory functions.
Information on the 21 available sizes and how to configure models.
Details on the available frame sizes for RV units, listed by model code.
Information on the refrigerant used, R407C, and its minimum water temperature.
Selection between Cooling only and Heat Pump models.
Selection of heat recovery versions: without, with desuperheater, or total recovery.
Selection of versions: Silenziata (L), Alta temperatura silenziata (A), Extra silenziata (E).
Choice between aluminium or copper fins for the coils.
Selection of evaporator compliance with PED, TUV-D, or UDT-PL standards.
Details on voltage supply and compressor protection types (fuses or magnetic).
Description of the high efficiency finned pack air side heat exchanger.
Description of the plate or shell and tube heat exchanger with insulation.
Information on the semi-hermetic mono-screw compressors used in the units.
Explanation of the filter-drier's role in removing impurities and moisture.
Purpose of the sight glass for checking refrigerant charge and moisture.
How the thermostatic valve regulates gas flow based on thermal load.
Purpose of liquid accumulator in heat pump or total recovery units.
Function of cocks for intercepting refrigerant during maintenance.
Protection against liquid refrigerant returns in heat pump models.
Description of the silencing system for even gas flow.
Function of the reversing valve for heating/cooling operation.
Excludes thermostatic valve during defrost cycle.
How the solenoid valve prevents gas flow when compressor stops.
Detects liquid temperature at expansion device input.
Details on axial-flow fans with static and dynamic balancing.
Description of the hot galvanised sheet steel frame with coating.
Safety feature allowing access to the electric panel after power cut.
Details on the sound-absorbent cover reducing noise and protecting compressors.
Description of the electrical cabinet conforming to EN standards.
Function of pressure switches for abnormal pressure cut-out.
Operation of safety valves for excessive pressure protection.
Function of the high pressure sensor for monitoring delivery pressure.
Function of the low pressure sensor for monitoring suction pressure.
Prevents ice formation in the evaporator during winter disuse.
Details on microprocessor functions, alarm management, parameter display, and settings.
How the boards manage compressor start-up and shutdown based on water temperature.
Explanation of FIFO logic for balancing compressor operating hours and start-stops.
Summary of alarm types and manual reset procedures.
Description of the accessory for connecting units to BMS supervision systems.
Details on spring vibration damper supports and model selection.
Function of the DCPX accessory for operation at low ambient temperatures.
Description of the grille protecting the external coil from impact.
Function of the PRV accessory for remote operation of the chiller.
Details on the ROMEO device for remote chiller control via mobile phone.
Details on Silenced (L), Extra-Silenced (E), and High Ambient Temperature (A) versions.
Details on heat pump models available in Silenced (HL) and Extra-Silenced (HE) versions.
Describes Total Recovery (T) and Desuperheater (D) options for heat recovery.
Explanation of the microprocessor control system and internal memory functions.
Information on the 21 available sizes and how to configure models.
Details on the available frame sizes for RV units, listed by model code.
Information on the refrigerant used, R407C, and its minimum water temperature.
Selection between Cooling only and Heat Pump models.
Selection of heat recovery versions: without, with desuperheater, or total recovery.
Selection of versions: Silenziata (L), Alta temperatura silenziata (A), Extra silenziata (E).
Choice between aluminium or copper fins for the coils.
Selection of evaporator compliance with PED, TUV-D, or UDT-PL standards.
Details on voltage supply and compressor protection types (fuses or magnetic).
Description of the high efficiency finned pack air side heat exchanger.
Description of the plate or shell and tube heat exchanger with insulation.
Information on the semi-hermetic mono-screw compressors used in the units.
Explanation of the filter-drier's role in removing impurities and moisture.
Purpose of the sight glass for checking refrigerant charge and moisture.
How the thermostatic valve regulates gas flow based on thermal load.
Purpose of liquid accumulator in heat pump or total recovery units.
Function of cocks for intercepting refrigerant during maintenance.
Protection against liquid refrigerant returns in heat pump models.
Description of the silencing system for even gas flow.
Function of the reversing valve for heating/cooling operation.
Excludes thermostatic valve during defrost cycle.
How the solenoid valve prevents gas flow when compressor stops.
Detects liquid temperature at expansion device input.
Details on axial-flow fans with static and dynamic balancing.
Description of the hot galvanised sheet steel frame with coating.
Safety feature allowing access to the electric panel after power cut.
Details on the sound-absorbent cover reducing noise and protecting compressors.
Description of the electrical cabinet conforming to EN standards.
Function of pressure switches for abnormal pressure cut-out.
Operation of safety valves for excessive pressure protection.
Function of the high pressure sensor for monitoring delivery pressure.
Function of the low pressure sensor for monitoring suction pressure.
Prevents ice formation in the evaporator during winter disuse.
Details on microprocessor functions, alarm management, parameter display, and settings.
How the boards manage compressor start-up and shutdown based on water temperature.
Explanation of FIFO logic for balancing compressor operating hours and start-stops.
Summary of alarm types and manual reset procedures.
Description of the accessory for connecting units to BMS supervision systems.
Details on spring vibration damper supports and model selection.
Function of the DCPX accessory for operation at low ambient temperatures.
Description of the grille protecting the external coil from impact.
Function of the PRV accessory for remote operation of the chiller.
Details on the ROMEO device for remote chiller control via mobile phone.
General
