Adjusting
Volume
Radio
Turn the
Rotary
encoder
until the desired sound is
obtained.
SOURCE/<!>
Rotary
encoder
• The initial mode is Distance mode.
Listening
to
Radio
~/ESC
I
Preset buttons
(1
through
6)
~/III
0..
lENT
TUNE/A.ME
I
.-
" _ _ _ -
..
- _.
....
,
t-.
BAND
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned
in
(Automatic
Seek Tuning).
Manual mode:
The frequency
is
manually tuned
in
steps (Manual tuning).
4 Press
I-4-olI
or
~
to tune in the desired station.
Holding
down
I-4-olI
or
~
will
change
the
frequency
continuously.
•
If
DIGITAL SEEK is set
to
ON. the SEEK UP/DOWNfunctions only
stop on digital station frequencies while receiving an HD Radio
broadcast. Refer to "Digital Seek ON/OFF Setting" (page
18).
1 Press SOURCE/<!> to select TUNER mode.
2 Press BAND repeatedly until the desired radio band
is displayed.
F1
(FM1)
~
F2
(FM2)
~
AM
..
~
F1
(FM1)
3 Press
TUNE/A.ME
to select the tuning mode.
OX
SEEK
(Distance mode)
~
SEEK
(Local mode)
~
OFF
(Manual mode)
-;
OX
SEEK
(Distance mode)
iTunes Tagging lets you
tag
songs
you hear
on
HD
Radio stations with
your new CDA·105
and
then preview, buy.
and
download them later
from your iTunes
Tagged
playlist
the
ne"t time you sync your iPod.
If
the unit
is
connected to aTagging compatible device, you
can
use
the
iTunes Tagging function. For details. refer to
the
Owner's Manual
of
the
Tagging compatible device.
This unit cannot receive
HD
Radio signals (digital terrestrial radio). In
order to activate
the
digital radio functions described below.
an
optional
HD
Radio Tuner module must
be
connected through
the
Ai·NET
bus.
Connectable to Remote
Control
Interface
Box
This unit may be controlled from the vehicle's audio controls.
An
optional Alpine Remote Control Interface Box must be
used. For details, contact your Alpine dealer.
• Pressing
~/ESC
returns to the previous SETUP mode.
•
If
/10
operation is performed
for
60 seconds. SETUP is canceled.
•
To
synchronize the clock to another clock/watch
or
radio time
announcement. press and hold
0..
/ENT
for
at least 2 seconds after
setting the "hour." Minutes will reset
to
00.
If
the display shows over
"30"
minutes when you do this. the time will advance one hour.
Controllable with Remote Control
This unit can be controlled with an optional Alpine remote
control.
For
details, consult your Alpine dealer.
Point the optional remote control transmitter at the remote
control sensor.
Remote control
sensor
c
'.il.)
Setting
the
Time
1 Press and hold
F/SETUP
for at least 2 seconds to
activate the SETUP selection mode.
2 Turn the
Rotary
encoder
to select CLOCK ADJUST,
and then press
o../ENT.
3 Turn the
Rotary
encoder
to set hour.
4 Press
o../ENT.
5 Repeat steps 3 and 4 above to set minute.
6 Press and hold
F/SETUP
for at least 2 seconds to
return to normal mode.
Activating
the
Audio Mute function
will
instantly lower
the
volume
level by 20 dB.
Press
MUTE
to activate the MUTE mode.
The
audio
level will
decrease
by
about
20
dB.
Pressing
MUTE
again will bring the audio back
to
its
previous level.
Lowering
Volume
Quickly
7
..
EN
To Next Page
Loading...
